Density calculators / Soils, powders & packing
A clear measure of matter.
Wet to Dry Density Calculator
Convert wet and dry bulk density using dry-basis moisture content.
Your measurements & units
Your result
Ready to calculateEnter your values and press Calculate. The result will open on the calculation page.
Published references · Clear assumptions · No sign-up
The method
Formula and calculation steps
ρdry=ρwet/(1+w); ρwet=ρdry(1+w), w as dry-mass fraction.
Convert wet and dry bulk density using dry-basis moisture content.
- Confirm the sample, reference state, measurement basis and units.
- Enter actual measurements and compatible reference values.
- Submit the form, then interpret the result with the assumptions and limits below.
Assumes the same total volume and conserved dry solid mass. Wet-basis moisture percentage is different.
Wet to Dry Density: method and interpretation
Convert wet and dry bulk density using dry-basis moisture content. Assumes the same total volume and conserved dry solid mass. Wet-basis moisture percentage is different.
Dry bulk density includes pore volume and excludes water mass; particle density excludes the spaces between solid particles. These quantities cannot be exchanged in porosity, slurry or phase-relationship equations without changing the meaning.
Soil relative density, relative compaction, zero-air-voids density and maximum laboratory dry density are different concepts. Powder tapping also depends on a stated test method. No acceptance limits or complete testing procedure are selected by these numerical tools.
Continue with: Soil Dry Bulk Density Calculator · Dry to Wet Density Calculator · Soil Porosity from Density Calculator · Saturated and Submerged Soil Density Calculator
Check the numbers
Wet to Dry Density Calculator: calculated examples
These scenarios are computed with the same method as the form. They are not product recommendations, code design values or complete standards tables.
Worked example with stated inputs
Wet bulk density = 1800 kg/m³; Dry-basis water content = 20 %.
| Output | Computed result |
|---|---|
| Dry bulk density | 1,500 kg/m³ |
| Mass density | 1.5 g/cm³ or g/mL |
| Mass density | 93.641941 lb/ft³ |
| Mass density | 0.054191 lb/in³ |
| Mass density | 12.518107 lb/US gal |
| Mass density | 15.033619 lb/Imperial gal |
How the stated input changes the result
| Scenario | Changed input / basis | Result |
|---|---|---|
| 10 % | Dry-basis water content | 1,636.363636 kg/m³ |
| 15 % | Dry-basis water content | 1,565.217391 kg/m³ |
| 20 % | Dry-basis water content | 1,500 kg/m³ |
| 25 % | Dry-basis water content | 1,440 kg/m³ |
| 30 % | Dry-basis water content | 1,384.615385 kg/m³ |
| 40 % | Dry-basis water content | 1,285.714286 kg/m³ |
Unchanged inputs use: Wet bulk density = 1800 kg/m³; Dry-basis water content = 20 %. Results retain the model limitations described above.
Common questions
What measurement or model limitation matters here?
Assumes the same total volume and conserved dry solid mass. Wet-basis moisture percentage is different.
How are the example tables calculated?
Each row changes the labelled dry-basis water content while retaining the other worked-example inputs. The table uses the same ρdry=ρwet/(1+w); ρwet=ρdry(1+w), w as dry-mass fraction. calculation as the form.
How do I use this wet to dry density calculator?
Convert wet and dry bulk density using dry-basis moisture content. ρdry=ρwet/(1+w); ρwet=ρdry(1+w), w as dry-mass fraction.
Which units should I enter?
Use the unit printed beside each input or chosen in its selector. The dimension-unit switch converts only the length or area fields that carry it. Other quantities retain their printed units. Mass density has dimensions M L⁻³; a ratio, number per area or probability density is a different quantity.
Are starting values measured material or reference data?
They are editable worked-example inputs unless a specific source and reference condition are explicitly identified. Measure or obtain the properties appropriate to the actual sample, temperature and method.
Can I export the result to Excel?
After calculating, Export CSV saves numerical results and submitted inputs. CSV is a text table, not an Excel formula workbook or a certified test report.
Where are the formula sources?
Full source addresses are printed below as ordinary text. The equations, worked examples and comparison tables are contained in these pages and do not require an online data service.
Related calculators
Formula sources and references
References support the underlying methods and units. Chosen example inputs are not universal recommendations, supplier ratings, market prices or code limits.
- FHWA NHI-05-037: Chapter 5, soil phase relationships and relative densityhttps://www.fhwa.dot.gov/engineering/geotech/pubs/05037/05a.cfm
- NIST Guide to the SI: conversion factorshttps://www.nist.gov/pml/special-publication-811/nist-guide-si-appendix-b-conversion-factors