Density CalculatorMeasure mass. Define volume.

Density calculators / Soils, powders & packing

A clear measure of matter.

Saturated and Submerged Soil Density Calculator

Calculate dry, partly saturated, saturated and buoyant-equivalent soil densities.

Your measurements & units

kg/m³
kg/m³
fraction

Starting values are editable examples. Confirm the sample, measurement basis and units. Dimension switching converts only the labelled geometry fields; other unit selectors describe the numbers you enter.

Reset

Your result

Ready to calculate

Enter your values and press Calculate. The result will open on the calculation page.

Published references · Clear assumptions · No sign-up

The method

Formula and calculation steps

ρ=(ρsolid+Sr e ρwater)/(1+e); ρsat=(ρsolid+eρwater)/(1+e); ρsub=ρsat−ρwater.

Calculate dry, partly saturated, saturated and buoyant-equivalent soil densities.

  1. Confirm the sample, reference state, measurement basis and units.
  2. Enter actual measurements and compatible reference values.
  3. Submit the form, then interpret the result with the assumptions and limits below.

Three-phase ideal volume accounting with negligible air mass; groundwater force and effective-stress analysis require the actual boundary conditions.

Saturated and Submerged Soil Density: method and interpretation

Calculate dry, partly saturated, saturated and buoyant-equivalent soil densities. Three-phase ideal volume accounting with negligible air mass; groundwater force and effective-stress analysis require the actual boundary conditions.

Dry bulk density includes pore volume and excludes water mass; particle density excludes the spaces between solid particles. These quantities cannot be exchanged in porosity, slurry or phase-relationship equations without changing the meaning.

Soil relative density, relative compaction, zero-air-voids density and maximum laboratory dry density are different concepts. Powder tapping also depends on a stated test method. No acceptance limits or complete testing procedure are selected by these numerical tools.

Check the numbers

Saturated and Submerged Soil Density Calculator: calculated examples

These scenarios are computed with the same method as the form. They are not product recommendations, code design values or complete standards tables.

Worked example with stated inputs

Solid particle density = 2650 kg/m³; Pore water density = 1000 kg/m³; Void ratio e = 0.6 ; Degree of saturation = 0.5 fraction.

OutputComputed result
Soil bulk density at supplied saturation1,843.75 kg/m³
Dry bulk density1,656.25 kg/m³
Saturated density2,031.25 kg/m³
Submerged equivalent density1,031.25 kg/m³
Porosity37.5 %
Mass density1.84375 g/cm³ or g/mL
Mass density115.101552 lb/ft³
Mass density0.06661 lb/in³
Mass density15.386839 lb/US gal
Mass density18.478824 lb/Imperial gal

How the stated input changes the result

ScenarioChanged input / basisResult
0.3 Void ratio e2,153.846154 kg/m³
0.45 Void ratio e1,982.758621 kg/m³
0.6 Void ratio e1,843.75 kg/m³
0.75 Void ratio e1,728.571429 kg/m³
0.9 Void ratio e1,631.578947 kg/m³
1.2 Void ratio e1,477.272727 kg/m³

Unchanged inputs use: Solid particle density = 2650 kg/m³; Pore water density = 1000 kg/m³; Void ratio e = 0.6 ; Degree of saturation = 0.5 fraction. Results retain the model limitations described above.

Common questions

What measurement or model limitation matters here?

Three-phase ideal volume accounting with negligible air mass; groundwater force and effective-stress analysis require the actual boundary conditions.

How are the example tables calculated?

Each row changes the labelled void ratio e while retaining the other worked-example inputs. The table uses the same ρ=(ρsolid+Sr e ρwater)/(1+e); ρsat=(ρsolid+eρwater)/(1+e); ρsub=ρsat−ρwater. calculation as the form.

How do I use this saturated and submerged soil density calculator?

Calculate dry, partly saturated, saturated and buoyant-equivalent soil densities. ρ=(ρsolid+Sr e ρwater)/(1+e); ρsat=(ρsolid+eρwater)/(1+e); ρsub=ρsat−ρwater.

Which units should I enter?

Use the unit printed beside each input or chosen in its selector. The dimension-unit switch converts only the length or area fields that carry it. Other quantities retain their printed units. Mass density has dimensions M L⁻³; a ratio, number per area or probability density is a different quantity.

Are starting values measured material or reference data?

They are editable worked-example inputs unless a specific source and reference condition are explicitly identified. Measure or obtain the properties appropriate to the actual sample, temperature and method.

Can I export the result to Excel?

After calculating, Export CSV saves numerical results and submitted inputs. CSV is a text table, not an Excel formula workbook or a certified test report.

Where are the formula sources?

Full source addresses are printed below as ordinary text. The equations, worked examples and comparison tables are contained in these pages and do not require an online data service.

Formula sources and references

References support the underlying methods and units. Chosen example inputs are not universal recommendations, supplier ratings, market prices or code limits.

  • FHWA NHI-05-037: Chapter 5, soil phase relationships and relative densityhttps://www.fhwa.dot.gov/engineering/geotech/pubs/05037/05a.cfm
  • NIST Guide to the SI: conversion factorshttps://www.nist.gov/pml/special-publication-811/nist-guide-si-appendix-b-conversion-factors