Density calculators / Mass, volume & units
A clear measure of matter.
Density Unit Converter
Convert g/cm³, g/mL, kg/m³, kg/L, lb/ft³, lb/in³ and gallon-based mass densities.
Your measurements & units
Your result
Ready to calculateEnter your values and press Calculate. The result will open on the calculation page.
Published references · Clear assumptions · No sign-up
The method
Formula and calculation steps
ρSI=entered value × input-unit factor; converted value=ρSI/output-unit factor.
Convert g/cm³, g/mL, kg/m³, kg/L, lb/ft³, lb/in³ and gallon-based mass densities.
- Confirm the sample, reference state, measurement basis and units.
- Enter actual measurements and compatible reference values.
- Submit the form, then interpret the result with the assumptions and limits below.
US gallons and Imperial gallons have different volumes. Unit conversion does not correct temperature or composition.
Density Unit Converter: method and interpretation
Convert g/cm³, g/mL, kg/m³, kg/L, lb/ft³, lb/in³ and gallon-based mass densities. US gallons and Imperial gallons have different volumes. Unit conversion does not correct temperature or composition.
Mass density compares mass with three-dimensional volume. A density value alone cannot identify both mass and volume: one further independent measurement is required. Units such as g/mL and kg/m³ can be converted without changing the physical sample.
A density triangle is an aid to rearranging ρ=m/V, not a separate physical law. Keep the measurement basis consistent, especially when converting bulk materials, powders or liquids whose temperature may change.
Continue with: Density Calculator · Mass from Density and Volume Calculator · Volume from Mass and Density Calculator · Specific Volume to Density Calculator
Check the numbers
Density Unit Converter: calculated examples
These scenarios are computed with the same method as the form. They are not product recommendations, code design values or complete standards tables.
Worked example with stated inputs
Density value = 1 ; Input density unit = g/cm³ / g/mL; Output density unit = kg/m³.
| Output | Computed result |
|---|---|
| Converted density | 1,000 kg/m³ |
| SI density | 1,000 kg/m³ |
| Mass density | 1 g/cm³ or g/mL |
| Mass density | 62.427961 lb/ft³ |
| Mass density | 0.036127 lb/in³ |
| Mass density | 8.345404 lb/US gal |
| Mass density | 10.022413 lb/Imperial gal |
How the stated input changes the result
| Scenario | Changed input / basis | Result |
|---|---|---|
| 0.5 | Density value | 500 kg/m³ |
| 0.75 | Density value | 750 kg/m³ |
| 1 | Density value | 1,000 kg/m³ |
| 1.25 | Density value | 1,250 kg/m³ |
| 1.5 | Density value | 1,500 kg/m³ |
| 2 | Density value | 2,000 kg/m³ |
Unchanged inputs use: Density value = 1 ; Input density unit = g/cm³ / g/mL; Output density unit = kg/m³. Results retain the model limitations described above.
Common questions
What measurement or model limitation matters here?
US gallons and Imperial gallons have different volumes. Unit conversion does not correct temperature or composition.
How are the example tables calculated?
Each row changes the labelled density value while retaining the other worked-example inputs. The table uses the same ρSI=entered value × input-unit factor; converted value=ρSI/output-unit factor. calculation as the form.
How do I use this density unit converter?
Convert g/cm³, g/mL, kg/m³, kg/L, lb/ft³, lb/in³ and gallon-based mass densities. ρSI=entered value × input-unit factor; converted value=ρSI/output-unit factor.
Which units should I enter?
Use the unit printed beside each input or chosen in its selector. The dimension-unit switch converts only the length or area fields that carry it. Other quantities retain their printed units. Mass density has dimensions M L⁻³; a ratio, number per area or probability density is a different quantity.
Are starting values measured material or reference data?
They are editable worked-example inputs unless a specific source and reference condition are explicitly identified. Measure or obtain the properties appropriate to the actual sample, temperature and method.
Can I export the result to Excel?
After calculating, Export CSV saves numerical results and submitted inputs. CSV is a text table, not an Excel formula workbook or a certified test report.
Where are the formula sources?
Full source addresses are printed below as ordinary text. The equations, worked examples and comparison tables are contained in these pages and do not require an online data service.
Related calculators
Formula sources and references
References support the underlying methods and units. Chosen example inputs are not universal recommendations, supplier ratings, market prices or code limits.
- OpenStax University Physics: density, pressure and mass per volumehttps://openstax.org/books/university-physics-volume-1/pages/14-1-fluids-density-and-pressure
- NIST Guide to the SI: conversion factorshttps://www.nist.gov/pml/special-publication-811/nist-guide-si-appendix-b-conversion-factors