Density CalculatorMeasure mass. Define volume.

Density calculators / Mass, volume & units

A clear measure of matter.

Specific Volume to Density Calculator

Convert specific volume to mass density and show reciprocal-unit examples.

Your measurements & units

m³/kg

Starting values are editable examples. Confirm the sample, measurement basis and units. Dimension switching converts only the labelled geometry fields; other unit selectors describe the numbers you enter.

Reset

Your result

Ready to calculate

Enter your values and press Calculate. The result will open on the calculation page.

Published references · Clear assumptions · No sign-up

The method

Formula and calculation steps

ρ=1/vspecific.

Convert specific volume to mass density and show reciprocal-unit examples.

  1. Confirm the sample, reference state, measurement basis and units.
  2. Enter actual measurements and compatible reference values.
  3. Submit the form, then interpret the result with the assumptions and limits below.

Specific volume is volume per mass, not a total volume and not specific gravity.

Specific Volume to Density: method and interpretation

Convert specific volume to mass density and show reciprocal-unit examples. Specific volume is volume per mass, not a total volume and not specific gravity.

Mass density compares mass with three-dimensional volume. A density value alone cannot identify both mass and volume: one further independent measurement is required. Units such as g/mL and kg/m³ can be converted without changing the physical sample.

A density triangle is an aid to rearranging ρ=m/V, not a separate physical law. Keep the measurement basis consistent, especially when converting bulk materials, powders or liquids whose temperature may change.

Check the numbers

Specific Volume to Density Calculator: calculated examples

These scenarios are computed with the same method as the form. They are not product recommendations, code design values or complete standards tables.

Worked example with stated inputs

Specific volume = 0.001 m³/kg.

OutputComputed result
Density from specific volume1,000 kg/m³
Mass density1 g/cm³ or g/mL
Mass density62.427961 lb/ft³
Mass density0.036127 lb/in³
Mass density8.345404 lb/US gal
Mass density10.022413 lb/Imperial gal

How the stated input changes the result

ScenarioChanged input / basisResult
0.0005 m³/kgSpecific volume2,000 kg/m³
0.00075 m³/kgSpecific volume1,333.333333 kg/m³
0.001 m³/kgSpecific volume1,000 kg/m³
0.00125 m³/kgSpecific volume800 kg/m³
0.0015 m³/kgSpecific volume666.666667 kg/m³
0.002 m³/kgSpecific volume500 kg/m³

Unchanged inputs use: Specific volume = 0.001 m³/kg. Results retain the model limitations described above.

Common questions

What measurement or model limitation matters here?

Specific volume is volume per mass, not a total volume and not specific gravity.

How are the example tables calculated?

Each row changes the labelled specific volume while retaining the other worked-example inputs. The table uses the same ρ=1/vspecific. calculation as the form.

How do I use this specific volume to density calculator?

Convert specific volume to mass density and show reciprocal-unit examples. ρ=1/vspecific.

Which units should I enter?

Use the unit printed beside each input or chosen in its selector. The dimension-unit switch converts only the length or area fields that carry it. Other quantities retain their printed units. Mass density has dimensions M L⁻³; a ratio, number per area or probability density is a different quantity.

Are starting values measured material or reference data?

They are editable worked-example inputs unless a specific source and reference condition are explicitly identified. Measure or obtain the properties appropriate to the actual sample, temperature and method.

Can I export the result to Excel?

After calculating, Export CSV saves numerical results and submitted inputs. CSV is a text table, not an Excel formula workbook or a certified test report.

Where are the formula sources?

Full source addresses are printed below as ordinary text. The equations, worked examples and comparison tables are contained in these pages and do not require an online data service.

Formula sources and references

References support the underlying methods and units. Chosen example inputs are not universal recommendations, supplier ratings, market prices or code limits.

  • OpenStax University Physics: density, pressure and mass per volumehttps://openstax.org/books/university-physics-volume-1/pages/14-1-fluids-density-and-pressure
  • NIST Guide to the SI: conversion factorshttps://www.nist.gov/pml/special-publication-811/nist-guide-si-appendix-b-conversion-factors