Density CalculatorMeasure mass. Define volume.

Density calculators / Soils, powders & packing

A clear measure of matter.

Soil Dry Bulk Density Calculator

Calculate soil dry bulk density from a defined core volume and oven-dry mass.

Your measurements & units

g
cm³

Starting values are editable examples. Confirm the sample, measurement basis and units. Dimension switching converts only the labelled geometry fields; other unit selectors describe the numbers you enter.

Reset

Your result

Ready to calculate

Enter your values and press Calculate. The result will open on the calculation page.

Published references · Clear assumptions · No sign-up

The method

Formula and calculation steps

ρdry=oven-dry solid mass / total sample volume, including pores.

Calculate soil dry bulk density from a defined core volume and oven-dry mass.

  1. Confirm the sample, reference state, measurement basis and units.
  2. Enter actual measurements and compatible reference values.
  3. Submit the form, then interpret the result with the assumptions and limits below.

Pores are included. Shrinkage and volume condition must match the test procedure; this is not particle density.

Soil Dry Bulk Density: method and interpretation

Calculate soil dry bulk density from a defined core volume and oven-dry mass. Pores are included. Shrinkage and volume condition must match the test procedure; this is not particle density.

Dry bulk density includes pore volume and excludes water mass; particle density excludes the spaces between solid particles. These quantities cannot be exchanged in porosity, slurry or phase-relationship equations without changing the meaning.

Soil relative density, relative compaction, zero-air-voids density and maximum laboratory dry density are different concepts. Powder tapping also depends on a stated test method. No acceptance limits or complete testing procedure are selected by these numerical tools.

Check the numbers

Soil Dry Bulk Density Calculator: calculated examples

These scenarios are computed with the same method as the form. They are not product recommendations, code design values or complete standards tables.

Worked example with stated inputs

Oven-dry solid mass = 130 g; Total sampled volume = 100 cm³.

OutputComputed result
Dry solid mass / total bulk volume1,300 kg/m³
Mass density1.3 g/cm³ or g/mL
Mass density81.156349 lb/ft³
Mass density0.046965 lb/in³
Mass density10.849026 lb/US gal
Mass density13.029137 lb/Imperial gal

How the stated input changes the result

ScenarioChanged input / basisResult
65 gOven-dry solid mass650 kg/m³
97.5 gOven-dry solid mass975 kg/m³
130 gOven-dry solid mass1,300 kg/m³
162.5 gOven-dry solid mass1,625 kg/m³
195 gOven-dry solid mass1,950 kg/m³
260 gOven-dry solid mass2,600 kg/m³

Unchanged inputs use: Oven-dry solid mass = 130 g; Total sampled volume = 100 cm³. Results retain the model limitations described above.

Common questions

What measurement or model limitation matters here?

Pores are included. Shrinkage and volume condition must match the test procedure; this is not particle density.

How are the example tables calculated?

Each row changes the labelled oven-dry solid mass while retaining the other worked-example inputs. The table uses the same ρdry=oven-dry solid mass / total sample volume, including pores. calculation as the form.

How do I use this soil dry bulk density calculator?

Calculate soil dry bulk density from a defined core volume and oven-dry mass. ρdry=oven-dry solid mass / total sample volume, including pores.

Which units should I enter?

Use the unit printed beside each input or chosen in its selector. The dimension-unit switch converts only the length or area fields that carry it. Other quantities retain their printed units. Mass density has dimensions M L⁻³; a ratio, number per area or probability density is a different quantity.

Are starting values measured material or reference data?

They are editable worked-example inputs unless a specific source and reference condition are explicitly identified. Measure or obtain the properties appropriate to the actual sample, temperature and method.

Can I export the result to Excel?

After calculating, Export CSV saves numerical results and submitted inputs. CSV is a text table, not an Excel formula workbook or a certified test report.

Where are the formula sources?

Full source addresses are printed below as ordinary text. The equations, worked examples and comparison tables are contained in these pages and do not require an online data service.

Formula sources and references

References support the underlying methods and units. Chosen example inputs are not universal recommendations, supplier ratings, market prices or code limits.

  • USDA NRCS: Soil Bulk Density / Moisture / Aerationhttps://www.nrcs.usda.gov/sites/default/files/2022-10/Soil%20Bulk%20Density%20Moisture%20Aeration.pdf
  • NIST Guide to the SI: conversion factorshttps://www.nist.gov/pml/special-publication-811/nist-guide-si-appendix-b-conversion-factors