Density CalculatorMeasure mass. Define volume.

Density calculators / Soils, powders & packing

A clear measure of matter.

Soil Porosity from Density Calculator

Calculate total pore fraction and void ratio from compatible bulk and particle densities.

Your measurements & units

kg/m³
kg/m³

Starting values are editable examples. Confirm the sample, measurement basis and units. Dimension switching converts only the labelled geometry fields; other unit selectors describe the numbers you enter.

Reset

Your result

Ready to calculate

Enter your values and press Calculate. The result will open on the calculation page.

Published references · Clear assumptions · No sign-up

The method

Formula and calculation steps

Porosity n=1−ρdry/ρparticle; void ratio e=ρparticle/ρdry−1.

Calculate total pore fraction and void ratio from compatible bulk and particle densities.

  1. Confirm the sample, reference state, measurement basis and units.
  2. Enter actual measurements and compatible reference values.
  3. Submit the form, then interpret the result with the assumptions and limits below.

Requires dry bulk density no greater than particle density. No density-log inversion, mineral identification or measured pore-size distribution.

Soil Porosity from Density: method and interpretation

Calculate total pore fraction and void ratio from compatible bulk and particle densities. Requires dry bulk density no greater than particle density. No density-log inversion, mineral identification or measured pore-size distribution.

Dry bulk density includes pore volume and excludes water mass; particle density excludes the spaces between solid particles. These quantities cannot be exchanged in porosity, slurry or phase-relationship equations without changing the meaning.

Soil relative density, relative compaction, zero-air-voids density and maximum laboratory dry density are different concepts. Powder tapping also depends on a stated test method. No acceptance limits or complete testing procedure are selected by these numerical tools.

Check the numbers

Soil Porosity from Density Calculator: calculated examples

These scenarios are computed with the same method as the form. They are not product recommendations, code design values or complete standards tables.

Worked example with stated inputs

Dry bulk density = 1500 kg/m³; Solid particle density = 2650 kg/m³.

OutputComputed result
Calculated pore volume fraction43.396226 %
Void ratio0.766667
Solid volume fraction0.566038

How the stated input changes the result

ScenarioChanged input / basisResult
1000 kg/m³Dry bulk density62.264151 %
1250 kg/m³Dry bulk density52.830189 %
1500 kg/m³Dry bulk density43.396226 %
1750 kg/m³Dry bulk density33.962264 %
2000 kg/m³Dry bulk density24.528302 %
2500 kg/m³Dry bulk density5.660377 %

Unchanged inputs use: Dry bulk density = 1500 kg/m³; Solid particle density = 2650 kg/m³. Results retain the model limitations described above.

Common questions

What measurement or model limitation matters here?

Requires dry bulk density no greater than particle density. No density-log inversion, mineral identification or measured pore-size distribution.

How are the example tables calculated?

Each row changes the labelled dry bulk density while retaining the other worked-example inputs. The table uses the same Porosity n=1−ρdry/ρparticle; void ratio e=ρparticle/ρdry−1. calculation as the form.

How do I use this soil porosity from density calculator?

Calculate total pore fraction and void ratio from compatible bulk and particle densities. Porosity n=1−ρdry/ρparticle; void ratio e=ρparticle/ρdry−1.

Which units should I enter?

Use the unit printed beside each input or chosen in its selector. The dimension-unit switch converts only the length or area fields that carry it. Other quantities retain their printed units. Mass density has dimensions M L⁻³; a ratio, number per area or probability density is a different quantity.

Are starting values measured material or reference data?

They are editable worked-example inputs unless a specific source and reference condition are explicitly identified. Measure or obtain the properties appropriate to the actual sample, temperature and method.

Can I export the result to Excel?

After calculating, Export CSV saves numerical results and submitted inputs. CSV is a text table, not an Excel formula workbook or a certified test report.

Where are the formula sources?

Full source addresses are printed below as ordinary text. The equations, worked examples and comparison tables are contained in these pages and do not require an online data service.

Formula sources and references

References support the underlying methods and units. Chosen example inputs are not universal recommendations, supplier ratings, market prices or code limits.

  • FHWA NHI-05-037: Chapter 5, soil phase relationships and relative densityhttps://www.fhwa.dot.gov/engineering/geotech/pubs/05037/05a.cfm
  • NIST Guide to the SI: conversion factorshttps://www.nist.gov/pml/special-publication-811/nist-guide-si-appendix-b-conversion-factors