Density CalculatorMeasure mass. Define volume.

Density calculators / Mixtures & composition

A clear measure of matter.

Slurry Solids Concentration Calculator

Infer slurry solids mass and volume fractions under a two-component additive-volume model.

Your measurements & units

kg/m³
kg/m³
kg/m³

Starting values are editable examples. Confirm the sample, measurement basis and units. Dimension switching converts only the labelled geometry fields; other unit selectors describe the numbers you enter.

Reset

Your result

Ready to calculate

Enter your values and press Calculate. The result will open on the calculation page.

Published references · Clear assumptions · No sign-up

The method

Formula and calculation steps

wsolid=(1/ρslurry−1/ρliquid)/(1/ρsolid−1/ρliquid).

Infer slurry solids mass and volume fractions under a two-component additive-volume model.

  1. Confirm the sample, reference state, measurement basis and units.
  2. Enter actual measurements and compatible reference values.
  3. Submit the form, then interpret the result with the assumptions and limits below.

Requires distinct component densities and slurry density between them. Entrained gas invalidates this simple inverse.

Slurry Solids Concentration: method and interpretation

Infer slurry solids mass and volume fractions under a two-component additive-volume model. Requires distinct component densities and slurry density between them. Entrained gas invalidates this simple inverse.

Mixture density requires a defined composition and a volume model. Adding the component masses is justified by mass conservation, but adding the separate component volumes is an additional assumption. Some solutions contract or expand when mixed.

Mass fraction, mole fraction and volume fraction have different denominators. The labels on this page state the basis actually used. A measured solution density alone does not identify a unique solute concentration without a separate substance-specific calibration.

Check the numbers

Slurry Solids Concentration Calculator: calculated examples

These scenarios are computed with the same method as the form. They are not product recommendations, code design values or complete standards tables.

Worked example with stated inputs

Measured slurry density = 1200 kg/m³; Solid particle density = 2650 kg/m³; Carrier liquid density = 1000 kg/m³.

OutputComputed result
Inferred slurry solids content26.767677 % by mass
Solids mass fraction0.267677
Solids mass percentage26.767677 %
Solids volume percentage12.121212 %

How the stated input changes the result

ScenarioChanged input / basisResult
1000 kg/m³Measured slurry density0 % by mass
1100 kg/m³Measured slurry density14.600551 % by mass
1200 kg/m³Measured slurry density26.767677 % by mass
1400 kg/m³Measured slurry density45.887446 % by mass
1800 kg/m³Measured slurry density71.380471 % by mass
2400 kg/m³Measured slurry density93.686869 % by mass

Unchanged inputs use: Measured slurry density = 1200 kg/m³; Solid particle density = 2650 kg/m³; Carrier liquid density = 1000 kg/m³. Results retain the model limitations described above.

Common questions

What measurement or model limitation matters here?

Requires distinct component densities and slurry density between them. Entrained gas invalidates this simple inverse.

How are the example tables calculated?

Each row changes the labelled measured slurry density while retaining the other worked-example inputs. The table uses the same wsolid=(1/ρslurry−1/ρliquid)/(1/ρsolid−1/ρliquid). calculation as the form.

How do I use this slurry solids concentration calculator?

Infer slurry solids mass and volume fractions under a two-component additive-volume model. wsolid=(1/ρslurry−1/ρliquid)/(1/ρsolid−1/ρliquid).

Which units should I enter?

Use the unit printed beside each input or chosen in its selector. The dimension-unit switch converts only the length or area fields that carry it. Other quantities retain their printed units. Mass density has dimensions M L⁻³; a ratio, number per area or probability density is a different quantity.

Are starting values measured material or reference data?

They are editable worked-example inputs unless a specific source and reference condition are explicitly identified. Measure or obtain the properties appropriate to the actual sample, temperature and method.

Can I export the result to Excel?

After calculating, Export CSV saves numerical results and submitted inputs. CSV is a text table, not an Excel formula workbook or a certified test report.

Where are the formula sources?

Full source addresses are printed below as ordinary text. The equations, worked examples and comparison tables are contained in these pages and do not require an online data service.

Formula sources and references

References support the underlying methods and units. Chosen example inputs are not universal recommendations, supplier ratings, market prices or code limits.

  • OpenStax University Physics: density, pressure and mass per volumehttps://openstax.org/books/university-physics-volume-1/pages/14-1-fluids-density-and-pressure
  • NIST Guide to the SI: conversion factorshttps://www.nist.gov/pml/special-publication-811/nist-guide-si-appendix-b-conversion-factors