Density CalculatorMeasure mass. Define volume.

Density calculators / Mixtures & composition

A clear measure of matter.

Slurry Density Calculator

Calculate a two-phase slurry density from solids mass fraction and component densities.

Your measurements & units

ratio
kg/m³
kg/m³

Starting values are editable examples. Confirm the sample, measurement basis and units. Dimension switching converts only the labelled geometry fields; other unit selectors describe the numbers you enter.

Reset

Your result

Ready to calculate

Enter your values and press Calculate. The result will open on the calculation page.

Published references · Clear assumptions · No sign-up

The method

Formula and calculation steps

1/ρslurry=wsolid/ρsolid+(1−wsolid)/ρliquid.

Calculate a two-phase slurry density from solids mass fraction and component densities.

  1. Confirm the sample, reference state, measurement basis and units.
  2. Enter actual measurements and compatible reference values.
  3. Submit the form, then interpret the result with the assumptions and limits below.

Particle and carrier volumes are additive; no entrained air, dissolved reaction or nonuniform settling.

Slurry Density: method and interpretation

Calculate a two-phase slurry density from solids mass fraction and component densities. Particle and carrier volumes are additive; no entrained air, dissolved reaction or nonuniform settling.

Mixture density requires a defined composition and a volume model. Adding the component masses is justified by mass conservation, but adding the separate component volumes is an additional assumption. Some solutions contract or expand when mixed.

Mass fraction, mole fraction and volume fraction have different denominators. The labels on this page state the basis actually used. A measured solution density alone does not identify a unique solute concentration without a separate substance-specific calibration.

Check the numbers

Slurry Density Calculator: calculated examples

These scenarios are computed with the same method as the form. They are not product recommendations, code design values or complete standards tables.

Worked example with stated inputs

Solids mass fraction = 0.3 ratio; Solid particle density = 2650 kg/m³; Carrier liquid density = 1000 kg/m³.

OutputComputed result
Two-phase additive-volume slurry density1,229.698376 kg/m³
Solids mass fraction0.3
Solids mass percentage30 %
Solids volume percentage13.921114 %
Mass density1.229698 g/cm³ or g/mL
Mass density76.767562 lb/ft³
Mass density0.044426 lb/in³
Mass density10.26233 lb/US gal
Mass density12.324545 lb/Imperial gal

How the stated input changes the result

ScenarioChanged input / basisResult
0.15 ratioSolids mass fraction1,103.01769 kg/m³
0.225 ratioSolids mass fraction1,162.918267 kg/m³
0.3 ratioSolids mass fraction1,229.698376 kg/m³
0.375 ratioSolids mass fraction1,304.615385 kg/m³
0.45 ratioSolids mass fraction1,389.252949 kg/m³
0.6 ratioSolids mass fraction1,596.385542 kg/m³

Unchanged inputs use: Solids mass fraction = 0.3 ratio; Solid particle density = 2650 kg/m³; Carrier liquid density = 1000 kg/m³. Results retain the model limitations described above.

Common questions

What measurement or model limitation matters here?

Particle and carrier volumes are additive; no entrained air, dissolved reaction or nonuniform settling.

How are the example tables calculated?

Each row changes the labelled solids mass fraction while retaining the other worked-example inputs. The table uses the same 1/ρslurry=wsolid/ρsolid+(1−wsolid)/ρliquid. calculation as the form.

How do I use this slurry density calculator?

Calculate a two-phase slurry density from solids mass fraction and component densities. 1/ρslurry=wsolid/ρsolid+(1−wsolid)/ρliquid.

Which units should I enter?

Use the unit printed beside each input or chosen in its selector. The dimension-unit switch converts only the length or area fields that carry it. Other quantities retain their printed units. Mass density has dimensions M L⁻³; a ratio, number per area or probability density is a different quantity.

Are starting values measured material or reference data?

They are editable worked-example inputs unless a specific source and reference condition are explicitly identified. Measure or obtain the properties appropriate to the actual sample, temperature and method.

Can I export the result to Excel?

After calculating, Export CSV saves numerical results and submitted inputs. CSV is a text table, not an Excel formula workbook or a certified test report.

Where are the formula sources?

Full source addresses are printed below as ordinary text. The equations, worked examples and comparison tables are contained in these pages and do not require an online data service.

Formula sources and references

References support the underlying methods and units. Chosen example inputs are not universal recommendations, supplier ratings, market prices or code limits.

  • OpenStax University Physics: density, pressure and mass per volumehttps://openstax.org/books/university-physics-volume-1/pages/14-1-fluids-density-and-pressure
  • NIST Guide to the SI: conversion factorshttps://www.nist.gov/pml/special-publication-811/nist-guide-si-appendix-b-conversion-factors