Density CalculatorMeasure mass. Define volume.

Density calculators / Mixtures & composition

A clear measure of matter.

Mixture Density by Mass Calculator

Calculate a three-component additive-volume mixture from supplied component properties.

Your measurements & units

kg
kg/m³
kg
kg/m³
kg
kg/m³

Starting values are editable examples. Confirm the sample, measurement basis and units. Dimension switching converts only the labelled geometry fields; other unit selectors describe the numbers you enter.

Reset

Your result

Ready to calculate

Enter your values and press Calculate. The result will open on the calculation page.

Published references · Clear assumptions · No sign-up

The method

Formula and calculation steps

ρmix=Σmi/Σ(mi/ρi)

Calculate a three-component additive-volume mixture from supplied component properties.

  1. Confirm the sample, reference state, measurement basis and units.
  2. Enter actual measurements and compatible reference values.
  3. Submit the form, then interpret the result with the assumptions and limits below.

Only additive volume and conserved mass. No automatic concentration-property correlation, thermal expansion or volume contraction.

Mixture Density by Mass: method and interpretation

Calculate a three-component additive-volume mixture from supplied component properties. Only additive volume and conserved mass. No automatic concentration-property correlation, thermal expansion or volume contraction.

Mixture density requires a defined composition and a volume model. Adding the component masses is justified by mass conservation, but adding the separate component volumes is an additional assumption. Some solutions contract or expand when mixed.

Mass fraction, mole fraction and volume fraction have different denominators. The labels on this page state the basis actually used. A measured solution density alone does not identify a unique solute concentration without a separate substance-specific calibration.

Check the numbers

Mixture Density by Mass Calculator: calculated examples

These scenarios are computed with the same method as the form. They are not product recommendations, code design values or complete standards tables.

Worked example with stated inputs

Component 1 mass = 1 kg; Component 1 density = 800 kg/m³; Component 2 mass = 2 kg; Component 2 density = 1000 kg/m³; Component 3 mass = 1 kg; Component 3 density = 1200 kg/m³.

OutputComputed result
Additive-volume mixture density979.591837 kg/m³
Total mass4 kg
Additive total volume0.004083 m³
Mass density0.979592 g/cm³ or g/mL
Mass density61.153921 lb/ft³
Mass density0.03539 lb/in³
Mass density8.17509 lb/US gal
Mass density9.817874 lb/Imperial gal

How the stated input changes the result

ScenarioChanged input / basisResult
0.5 kgComponent 1 mass1,012.048193 kg/m³
0.75 kgComponent 1 mass994.475138 kg/m³
1 kgComponent 1 mass979.591837 kg/m³
1.25 kgComponent 1 mass966.824645 kg/m³
1.5 kgComponent 1 mass955.752212 kg/m³
2 kgComponent 1 mass937.5 kg/m³

Unchanged inputs use: Component 1 mass = 1 kg; Component 1 density = 800 kg/m³; Component 2 mass = 2 kg; Component 2 density = 1000 kg/m³; Component 3 mass = 1 kg; Component 3 density = 1200 kg/m³. Results retain the model limitations described above.

Common questions

What measurement or model limitation matters here?

Only additive volume and conserved mass. No automatic concentration-property correlation, thermal expansion or volume contraction.

How are the example tables calculated?

Each row changes the labelled component 1 mass while retaining the other worked-example inputs. The table uses the same ρmix=Σmi/Σ(mi/ρi) calculation as the form.

How do I use this mixture density by mass calculator?

Calculate a three-component additive-volume mixture from supplied component properties. ρmix=Σmi/Σ(mi/ρi)

Which units should I enter?

Use the unit printed beside each input or chosen in its selector. The dimension-unit switch converts only the length or area fields that carry it. Other quantities retain their printed units. Mass density has dimensions M L⁻³; a ratio, number per area or probability density is a different quantity.

Are starting values measured material or reference data?

They are editable worked-example inputs unless a specific source and reference condition are explicitly identified. Measure or obtain the properties appropriate to the actual sample, temperature and method.

Can I export the result to Excel?

After calculating, Export CSV saves numerical results and submitted inputs. CSV is a text table, not an Excel formula workbook or a certified test report.

Where are the formula sources?

Full source addresses are printed below as ordinary text. The equations, worked examples and comparison tables are contained in these pages and do not require an online data service.

Formula sources and references

References support the underlying methods and units. Chosen example inputs are not universal recommendations, supplier ratings, market prices or code limits.

  • OpenStax University Physics: density, pressure and mass per volumehttps://openstax.org/books/university-physics-volume-1/pages/14-1-fluids-density-and-pressure
  • NIST Guide to the SI: conversion factorshttps://www.nist.gov/pml/special-publication-811/nist-guide-si-appendix-b-conversion-factors