Density CalculatorMeasure mass. Define volume.

Density calculators / Soils, powders & packing

A clear measure of matter.

Packing Density Calculator

Calculate occupied solid volume fraction and remaining void fraction.

Your measurements & units

mL
mL

Starting values are editable examples. Confirm the sample, measurement basis and units. Dimension switching converts only the labelled geometry fields; other unit selectors describe the numbers you enter.

Reset

Your result

Ready to calculate

Enter your values and press Calculate. The result will open on the calculation page.

Published references · Clear assumptions · No sign-up

The method

Formula and calculation steps

Packing fraction=solid volume/bulk volume; void fraction=1−packing fraction.

Calculate occupied solid volume fraction and remaining void fraction.

  1. Confirm the sample, reference state, measurement basis and units.
  2. Enter actual measurements and compatible reference values.
  3. Submit the form, then interpret the result with the assumptions and limits below.

Solid volume cannot exceed the container volume. This does not optimize particle packing or infer pore-free volume from a shape name.

Packing Density: method and interpretation

Calculate occupied solid volume fraction and remaining void fraction. Solid volume cannot exceed the container volume. This does not optimize particle packing or infer pore-free volume from a shape name.

Dry bulk density includes pore volume and excludes water mass; particle density excludes the spaces between solid particles. These quantities cannot be exchanged in porosity, slurry or phase-relationship equations without changing the meaning.

Soil relative density, relative compaction, zero-air-voids density and maximum laboratory dry density are different concepts. Powder tapping also depends on a stated test method. No acceptance limits or complete testing procedure are selected by these numerical tools.

Check the numbers

Packing Density Calculator: calculated examples

These scenarios are computed with the same method as the form. They are not product recommendations, code design values or complete standards tables.

Worked example with stated inputs

Known solid material volume = 60 mL; Container bulk volume = 100 mL.

OutputComputed result
Solid packing fraction60 %
Void fraction40 %

How the stated input changes the result

ScenarioChanged input / basisResult
20 mLKnown solid material volume20 %
40 mLKnown solid material volume40 %
60 mLKnown solid material volume60 %
70 mLKnown solid material volume70 %
80 mLKnown solid material volume80 %
100 mLKnown solid material volume100 %

Unchanged inputs use: Known solid material volume = 60 mL; Container bulk volume = 100 mL. Results retain the model limitations described above.

Common questions

What measurement or model limitation matters here?

Solid volume cannot exceed the container volume. This does not optimize particle packing or infer pore-free volume from a shape name.

How are the example tables calculated?

Each row changes the labelled known solid material volume while retaining the other worked-example inputs. The table uses the same Packing fraction=solid volume/bulk volume; void fraction=1−packing fraction. calculation as the form.

How do I use this packing density calculator?

Calculate occupied solid volume fraction and remaining void fraction. Packing fraction=solid volume/bulk volume; void fraction=1−packing fraction.

Which units should I enter?

Use the unit printed beside each input or chosen in its selector. The dimension-unit switch converts only the length or area fields that carry it. Other quantities retain their printed units. Mass density has dimensions M L⁻³; a ratio, number per area or probability density is a different quantity.

Are starting values measured material or reference data?

They are editable worked-example inputs unless a specific source and reference condition are explicitly identified. Measure or obtain the properties appropriate to the actual sample, temperature and method.

Can I export the result to Excel?

After calculating, Export CSV saves numerical results and submitted inputs. CSV is a text table, not an Excel formula workbook or a certified test report.

Where are the formula sources?

Full source addresses are printed below as ordinary text. The equations, worked examples and comparison tables are contained in these pages and do not require an online data service.

Formula sources and references

References support the underlying methods and units. Chosen example inputs are not universal recommendations, supplier ratings, market prices or code limits.

  • OpenStax University Physics: density, pressure and mass per volumehttps://openstax.org/books/university-physics-volume-1/pages/14-1-fluids-density-and-pressure
  • NIST Guide to the SI: conversion factorshttps://www.nist.gov/pml/special-publication-811/nist-guide-si-appendix-b-conversion-factors