Density CalculatorMeasure mass. Define volume.

Density calculators / Relative density & reference states

A clear measure of matter.

Density to API Gravity Calculator

Convert the petroleum API gravity convention and density on an explicit 60°F reference basis.

Your measurements & units

kg/m³
kg/m³

Starting values are editable examples. Confirm the sample, measurement basis and units. Dimension switching converts only the labelled geometry fields; other unit selectors describe the numbers you enter.

Reset

Your result

Ready to calculate

Enter your values and press Calculate. The result will open on the calculation page.

Published references · Clear assumptions · No sign-up

The method

Formula and calculation steps

API=141.5/SG(60°F/60°F)−131.5; SG=ρoil,60/ρwater,60.

Convert the petroleum API gravity convention and density on an explicit 60°F reference basis.

  1. Confirm the sample, reference state, measurement basis and units.
  2. Enter actual measurements and compatible reference values.
  3. Submit the form, then interpret the result with the assumptions and limits below.

Inputs must already be at the stated reference state. This calculation does not correct operating-temperature density, fuel batches or pressure.

Density to API Gravity: method and interpretation

Convert the petroleum API gravity convention and density on an explicit 60°F reference basis. Inputs must already be at the stated reference state. This calculation does not correct operating-temperature density, fuel batches or pressure.

Reference temperature and reference material are part of a relative-density definition. Specific gravity is a ratio and has no mass-density unit. API gravity is a particular petroleum convention; it is not a general temperature correction.

Confirm that the sample and reference inputs already use the required conditions. A constant expansion coefficient is a declared local approximation, whereas a full petroleum or real-fluid property method needs additional composition and state data.

Check the numbers

Density to API Gravity Calculator: calculated examples

These scenarios are computed with the same method as the form. They are not product recommendations, code design values or complete standards tables.

Worked example with stated inputs

Oil density at 60°F = 850 kg/m³; Water reference density at 60°F = 999.016 kg/m³.

OutputComputed result
API gravity on supplied 60°F density basis34.806781 °API
Specific gravity at 60°F/60°F0.850837

How the stated input changes the result

ScenarioChanged input / basisResult
425 kg/m³Oil density at 60°F201.113562 °API
637.5 kg/m³Oil density at 60°F90.242375 °API
850 kg/m³Oil density at 60°F34.806781 °API
1062.5 kg/m³Oil density at 60°F1.545425 °API
1275 kg/m³Oil density at 60°F-20.628813 °API
1700 kg/m³Oil density at 60°F-48.346609 °API

Unchanged inputs use: Oil density at 60°F = 850 kg/m³; Water reference density at 60°F = 999.016 kg/m³. Results retain the model limitations described above.

Common questions

What measurement or model limitation matters here?

Inputs must already be at the stated reference state. This calculation does not correct operating-temperature density, fuel batches or pressure.

How are the example tables calculated?

Each row changes the labelled oil density at 60°f while retaining the other worked-example inputs. The table uses the same API=141.5/SG(60°F/60°F)−131.5; SG=ρoil,60/ρwater,60. calculation as the form.

How do I use this density to api gravity calculator?

Convert the petroleum API gravity convention and density on an explicit 60°F reference basis. API=141.5/SG(60°F/60°F)−131.5; SG=ρoil,60/ρwater,60.

Which units should I enter?

Use the unit printed beside each input or chosen in its selector. The dimension-unit switch converts only the length or area fields that carry it. Other quantities retain their printed units. Mass density has dimensions M L⁻³; a ratio, number per area or probability density is a different quantity.

Are starting values measured material or reference data?

They are editable worked-example inputs unless a specific source and reference condition are explicitly identified. Measure or obtain the properties appropriate to the actual sample, temperature and method.

Can I export the result to Excel?

After calculating, Export CSV saves numerical results and submitted inputs. CSV is a text table, not an Excel formula workbook or a certified test report.

Where are the formula sources?

Full source addresses are printed below as ordinary text. The equations, worked examples and comparison tables are contained in these pages and do not require an online data service.

Formula sources and references

References support the underlying methods and units. Chosen example inputs are not universal recommendations, supplier ratings, market prices or code limits.

  • US EIA: API gravity definition and 60°F/60°F specific-gravity formulahttps://www.eia.gov/dnav/pet/TblDefs/pet_crd_api_tbldef2.asp
  • NIST Guide to the SI: conversion factorshttps://www.nist.gov/pml/special-publication-811/nist-guide-si-appendix-b-conversion-factors