Density CalculatorMeasure mass. Define volume.

Density calculators / Relative density & reference states

A clear measure of matter.

Specific Gravity to Density Calculator

Convert relative density to physical density at the chosen reference condition.

Your measurements & units

ratio
kg/m³

Starting values are editable examples. Confirm the sample, measurement basis and units. Dimension switching converts only the labelled geometry fields; other unit selectors describe the numbers you enter.

Reset

Your result

Ready to calculate

Enter your values and press Calculate. The result will open on the calculation page.

Published references · Clear assumptions · No sign-up

The method

Formula and calculation steps

ρsample=SG × ρreference.

Convert relative density to physical density at the chosen reference condition.

  1. Confirm the sample, reference state, measurement basis and units.
  2. Enter actual measurements and compatible reference values.
  3. Submit the form, then interpret the result with the assumptions and limits below.

Reference density is an editable example; it must match the SG definition and temperature of the measurement.

Specific Gravity to Density: method and interpretation

Convert relative density to physical density at the chosen reference condition. Reference density is an editable example; it must match the SG definition and temperature of the measurement.

Reference temperature and reference material are part of a relative-density definition. Specific gravity is a ratio and has no mass-density unit. API gravity is a particular petroleum convention; it is not a general temperature correction.

Confirm that the sample and reference inputs already use the required conditions. A constant expansion coefficient is a declared local approximation, whereas a full petroleum or real-fluid property method needs additional composition and state data.

Check the numbers

Specific Gravity to Density Calculator: calculated examples

These scenarios are computed with the same method as the form. They are not product recommendations, code design values or complete standards tables.

Worked example with stated inputs

Specific gravity = 0.85 ratio; Reference fluid density = 999.1 kg/m³.

OutputComputed result
Mass density on supplied SG basis849.235 kg/m³
Mass density0.849235 g/cm³ or g/mL
Mass density53.016009 lb/ft³
Mass density0.030681 lb/in³
Mass density7.08721 lb/US gal
Mass density8.511384 lb/Imperial gal

How the stated input changes the result

ScenarioChanged input / basisResult
0.425 ratioSpecific gravity424.6175 kg/m³
0.6375 ratioSpecific gravity636.92625 kg/m³
0.85 ratioSpecific gravity849.235 kg/m³
1.0625 ratioSpecific gravity1,061.54375 kg/m³
1.275 ratioSpecific gravity1,273.8525 kg/m³
1.7 ratioSpecific gravity1,698.47 kg/m³

Unchanged inputs use: Specific gravity = 0.85 ratio; Reference fluid density = 999.1 kg/m³. Results retain the model limitations described above.

Common questions

What measurement or model limitation matters here?

Reference density is an editable example; it must match the SG definition and temperature of the measurement.

How are the example tables calculated?

Each row changes the labelled specific gravity while retaining the other worked-example inputs. The table uses the same ρsample=SG × ρreference. calculation as the form.

How do I use this specific gravity to density calculator?

Convert relative density to physical density at the chosen reference condition. ρsample=SG × ρreference.

Which units should I enter?

Use the unit printed beside each input or chosen in its selector. The dimension-unit switch converts only the length or area fields that carry it. Other quantities retain their printed units. Mass density has dimensions M L⁻³; a ratio, number per area or probability density is a different quantity.

Are starting values measured material or reference data?

They are editable worked-example inputs unless a specific source and reference condition are explicitly identified. Measure or obtain the properties appropriate to the actual sample, temperature and method.

Can I export the result to Excel?

After calculating, Export CSV saves numerical results and submitted inputs. CSV is a text table, not an Excel formula workbook or a certified test report.

Where are the formula sources?

Full source addresses are printed below as ordinary text. The equations, worked examples and comparison tables are contained in these pages and do not require an online data service.

Formula sources and references

References support the underlying methods and units. Chosen example inputs are not universal recommendations, supplier ratings, market prices or code limits.

  • OpenStax University Physics: density, pressure and mass per volumehttps://openstax.org/books/university-physics-volume-1/pages/14-1-fluids-density-and-pressure
  • NIST Guide to the SI: conversion factorshttps://www.nist.gov/pml/special-publication-811/nist-guide-si-appendix-b-conversion-factors