Density CalculatorMeasure mass. Define volume.

Density calculators / Relative density & reference states

A clear measure of matter.

Specific Gravity Calculator

Calculate a dimensionless relative density using an explicitly supplied reference density.

Your measurements & units

kg/m³

Starting values are editable examples. Confirm the sample, measurement basis and units. Dimension switching converts only the labelled geometry fields; other unit selectors describe the numbers you enter.

Reset

Your result

Ready to calculate

Enter your values and press Calculate. The result will open on the calculation page.

Published references · Clear assumptions · No sign-up

The method

Formula and calculation steps

SG=ρsample/ρreference.

Calculate a dimensionless relative density using an explicitly supplied reference density.

  1. Confirm the sample, reference state, measurement basis and units.
  2. Enter actual measurements and compatible reference values.
  3. Submit the form, then interpret the result with the assumptions and limits below.

Sample and reference temperatures must be stated. Water density is not exactly 1000 kg/m³ at every temperature.

Specific Gravity: method and interpretation

Calculate a dimensionless relative density using an explicitly supplied reference density. Sample and reference temperatures must be stated. Water density is not exactly 1000 kg/m³ at every temperature.

Reference temperature and reference material are part of a relative-density definition. Specific gravity is a ratio and has no mass-density unit. API gravity is a particular petroleum convention; it is not a general temperature correction.

Confirm that the sample and reference inputs already use the required conditions. A constant expansion coefficient is a declared local approximation, whereas a full petroleum or real-fluid property method needs additional composition and state data.

Check the numbers

Specific Gravity Calculator: calculated examples

These scenarios are computed with the same method as the form. They are not product recommendations, code design values or complete standards tables.

Worked example with stated inputs

Mass density = 1000 ; Density unit = kg/m³; Reference fluid density = 1000 kg/m³.

OutputComputed result
Specific gravity on supplied reference1 dimensionless
Sample density1,000 kg/m³
Reference density1,000 kg/m³

How the stated input changes the result

ScenarioChanged input / basisResult
500 Mass density0.5 dimensionless
750 Mass density0.75 dimensionless
1000 Mass density1 dimensionless
1250 Mass density1.25 dimensionless
1500 Mass density1.5 dimensionless
2000 Mass density2 dimensionless

Unchanged inputs use: Mass density = 1000 ; Density unit = kg/m³; Reference fluid density = 1000 kg/m³. Results retain the model limitations described above.

Common questions

What measurement or model limitation matters here?

Sample and reference temperatures must be stated. Water density is not exactly 1000 kg/m³ at every temperature.

How are the example tables calculated?

Each row changes the labelled mass density while retaining the other worked-example inputs. The table uses the same SG=ρsample/ρreference. calculation as the form.

How do I use this specific gravity calculator?

Calculate a dimensionless relative density using an explicitly supplied reference density. SG=ρsample/ρreference.

Which units should I enter?

Use the unit printed beside each input or chosen in its selector. The dimension-unit switch converts only the length or area fields that carry it. Other quantities retain their printed units. Mass density has dimensions M L⁻³; a ratio, number per area or probability density is a different quantity.

Are starting values measured material or reference data?

They are editable worked-example inputs unless a specific source and reference condition are explicitly identified. Measure or obtain the properties appropriate to the actual sample, temperature and method.

Can I export the result to Excel?

After calculating, Export CSV saves numerical results and submitted inputs. CSV is a text table, not an Excel formula workbook or a certified test report.

Where are the formula sources?

Full source addresses are printed below as ordinary text. The equations, worked examples and comparison tables are contained in these pages and do not require an online data service.

Formula sources and references

References support the underlying methods and units. Chosen example inputs are not universal recommendations, supplier ratings, market prices or code limits.

  • OpenStax University Physics: density, pressure and mass per volumehttps://openstax.org/books/university-physics-volume-1/pages/14-1-fluids-density-and-pressure
  • NIST Guide to the SI: conversion factorshttps://www.nist.gov/pml/special-publication-811/nist-guide-si-appendix-b-conversion-factors