Density CalculatorMeasure mass. Define volume.

Density calculators / Object geometry & measurement

A clear measure of matter.

Cylinder Density Calculator

Calculate sample density from measured mass and cylinder dimensions.

Your measurements & units

mm
mm

Starting values are editable examples. Confirm the sample, measurement basis and units. Dimension switching converts only the labelled geometry fields; other unit selectors describe the numbers you enter.

Reset

Your result

Ready to calculate

Enter your values and press Calculate. The result will open on the calculation page.

Published references · Clear assumptions · No sign-up

The method

Formula and calculation steps

V=πD²h/4; ρ=m/V.

Calculate sample density from measured mass and cylinder dimensions.

  1. Confirm the sample, reference state, measurement basis and units.
  2. Enter actual measurements and compatible reference values.
  3. Submit the form, then interpret the result with the assumptions and limits below.

The shape is idealized and solid. Cavities, pores, coatings and measurement tolerances affect the inferred density.

Cylinder Density: method and interpretation

Calculate sample density from measured mass and cylinder dimensions. The shape is idealized and solid. Cavities, pores, coatings and measurement tolerances affect the inferred density.

Measure actual sample dimensions and tare any container before weighing. A hollow object’s outside envelope gives apparent average density, while material-only volume gives a different quantity. Liquid displacement can fail when a sample absorbs, dissolves or traps air.

Density is sensitive to dimensional measurement: cylinder and sphere volume contain a squared or cubed dimension. The comparison table varies the stated measurement and assumes the remaining measurements are exact; it is not a laboratory uncertainty budget.

Check the numbers

Cylinder Density Calculator: calculated examples

These scenarios are computed with the same method as the form. They are not product recommendations, code design values or complete standards tables.

Worked example with stated inputs

Dimension units = Metric dimensions; Measured mass = 1 ; Mass unit = kg; Measured diameter = 100 mm; Measured height = 100 mm.

OutputComputed result
Density from measured shape1,273.239545 kg/m³
Measured / envelope volume0.000785 m³
Measured / envelope volume0.027736 ft³
Mass1 kg
Mass density1.27324 g/cm³ or g/mL
Mass density79.485748 lb/ft³
Mass density0.045999 lb/in³
Mass density10.625699 lb/US gal
Mass density12.760932 lb/Imperial gal

How the stated input changes the result

ScenarioChanged input / basisResult
50 mmMeasured diameter5,092.958179 kg/m³
75 mmMeasured diameter2,263.536968 kg/m³
100 mmMeasured diameter1,273.239545 kg/m³
125 mmMeasured diameter814.873309 kg/m³
150 mmMeasured diameter565.884242 kg/m³
200 mmMeasured diameter318.309886 kg/m³

Unchanged inputs use: Dimension units = Metric dimensions; Measured mass = 1 ; Mass unit = kg; Measured diameter = 100 mm; Measured height = 100 mm. Results retain the model limitations described above.

Common questions

What measurement or model limitation matters here?

The shape is idealized and solid. Cavities, pores, coatings and measurement tolerances affect the inferred density.

How are the example tables calculated?

Each row changes the labelled measured diameter while retaining the other worked-example inputs. The table uses the same V=πD²h/4; ρ=m/V. calculation as the form.

How do I use this cylinder density calculator?

Calculate sample density from measured mass and cylinder dimensions. V=πD²h/4; ρ=m/V.

Which units should I enter?

Use the unit printed beside each input or chosen in its selector. The dimension-unit switch converts only the length or area fields that carry it. Other quantities retain their printed units. Mass density has dimensions M L⁻³; a ratio, number per area or probability density is a different quantity.

Are starting values measured material or reference data?

They are editable worked-example inputs unless a specific source and reference condition are explicitly identified. Measure or obtain the properties appropriate to the actual sample, temperature and method.

Can I export the result to Excel?

After calculating, Export CSV saves numerical results and submitted inputs. CSV is a text table, not an Excel formula workbook or a certified test report.

Where are the formula sources?

Full source addresses are printed below as ordinary text. The equations, worked examples and comparison tables are contained in these pages and do not require an online data service.

Formula sources and references

References support the underlying methods and units. Chosen example inputs are not universal recommendations, supplier ratings, market prices or code limits.

  • OpenStax Prealgebra: geometry applications, volume and surface areahttps://openstax.org/books/prealgebra/pages/9-6-solve-geometry-applications-volume-and-surface-area
  • OpenStax University Physics: density, pressure and mass per volumehttps://openstax.org/books/university-physics-volume-1/pages/14-1-fluids-density-and-pressure
  • NIST Guide to the SI: conversion factorshttps://www.nist.gov/pml/special-publication-811/nist-guide-si-appendix-b-conversion-factors