Density calculators / Object geometry & measurement
A clear measure of matter.
Rectangular Object Density Calculator
Calculate sample density from measured mass and rectangular object dimensions.
Your measurements & units
Your result
Ready to calculateEnter your values and press Calculate. The result will open on the calculation page.
Published references · Clear assumptions · No sign-up
The method
Formula and calculation steps
V=length × width × height; ρ=m/V.
Calculate sample density from measured mass and rectangular object dimensions.
- Confirm the sample, reference state, measurement basis and units.
- Enter actual measurements and compatible reference values.
- Submit the form, then interpret the result with the assumptions and limits below.
The shape is idealized and solid. Cavities, pores, coatings and measurement tolerances affect the inferred density.
Rectangular Object Density: method and interpretation
Calculate sample density from measured mass and rectangular object dimensions. The shape is idealized and solid. Cavities, pores, coatings and measurement tolerances affect the inferred density.
Measure actual sample dimensions and tare any container before weighing. A hollow object’s outside envelope gives apparent average density, while material-only volume gives a different quantity. Liquid displacement can fail when a sample absorbs, dissolves or traps air.
Density is sensitive to dimensional measurement: cylinder and sphere volume contain a squared or cubed dimension. The comparison table varies the stated measurement and assumes the remaining measurements are exact; it is not a laboratory uncertainty budget.
Continue with: Cube Density Calculator · Cylinder Density Calculator · Sphere Density Calculator · Water Displacement Density Calculator
Check the numbers
Rectangular Object Density Calculator: calculated examples
These scenarios are computed with the same method as the form. They are not product recommendations, code design values or complete standards tables.
Worked example with stated inputs
Dimension units = Metric dimensions; Measured mass = 1 ; Mass unit = kg; Measured length = 100 mm; Measured width = 100 mm; Measured height = 100 mm.
| Output | Computed result |
|---|---|
| Density from measured shape | 1,000 kg/m³ |
| Measured / envelope volume | 0.001 m³ |
| Measured / envelope volume | 0.035315 ft³ |
| Mass | 1 kg |
| Mass density | 1 g/cm³ or g/mL |
| Mass density | 62.427961 lb/ft³ |
| Mass density | 0.036127 lb/in³ |
| Mass density | 8.345404 lb/US gal |
| Mass density | 10.022413 lb/Imperial gal |
How the stated input changes the result
| Scenario | Changed input / basis | Result |
|---|---|---|
| 50 mm | Measured length | 2,000 kg/m³ |
| 75 mm | Measured length | 1,333.333333 kg/m³ |
| 100 mm | Measured length | 1,000 kg/m³ |
| 125 mm | Measured length | 800 kg/m³ |
| 150 mm | Measured length | 666.666667 kg/m³ |
| 200 mm | Measured length | 500 kg/m³ |
Unchanged inputs use: Dimension units = Metric dimensions; Measured mass = 1 ; Mass unit = kg; Measured length = 100 mm; Measured width = 100 mm; Measured height = 100 mm. Results retain the model limitations described above.
Common questions
What measurement or model limitation matters here?
The shape is idealized and solid. Cavities, pores, coatings and measurement tolerances affect the inferred density.
How are the example tables calculated?
Each row changes the labelled measured length while retaining the other worked-example inputs. The table uses the same V=length × width × height; ρ=m/V. calculation as the form.
How do I use this rectangular object density calculator?
Calculate sample density from measured mass and rectangular object dimensions. V=length × width × height; ρ=m/V.
Which units should I enter?
Use the unit printed beside each input or chosen in its selector. The dimension-unit switch converts only the length or area fields that carry it. Other quantities retain their printed units. Mass density has dimensions M L⁻³; a ratio, number per area or probability density is a different quantity.
Are starting values measured material or reference data?
They are editable worked-example inputs unless a specific source and reference condition are explicitly identified. Measure or obtain the properties appropriate to the actual sample, temperature and method.
Can I export the result to Excel?
After calculating, Export CSV saves numerical results and submitted inputs. CSV is a text table, not an Excel formula workbook or a certified test report.
Where are the formula sources?
Full source addresses are printed below as ordinary text. The equations, worked examples and comparison tables are contained in these pages and do not require an online data service.
Related calculators
Formula sources and references
References support the underlying methods and units. Chosen example inputs are not universal recommendations, supplier ratings, market prices or code limits.
- OpenStax Prealgebra: geometry applications, volume and surface areahttps://openstax.org/books/prealgebra/pages/9-6-solve-geometry-applications-volume-and-surface-area
- OpenStax University Physics: density, pressure and mass per volumehttps://openstax.org/books/university-physics-volume-1/pages/14-1-fluids-density-and-pressure
- NIST Guide to the SI: conversion factorshttps://www.nist.gov/pml/special-publication-811/nist-guide-si-appendix-b-conversion-factors