Density CalculatorMeasure mass. Define volume.

Density calculators / Object geometry & measurement

A clear measure of matter.

Cube Density Calculator

Calculate sample density from measured mass and cube dimensions.

Your measurements & units

mm

Starting values are editable examples. Confirm the sample, measurement basis and units. Dimension switching converts only the labelled geometry fields; other unit selectors describe the numbers you enter.

Reset

Your result

Ready to calculate

Enter your values and press Calculate. The result will open on the calculation page.

Published references · Clear assumptions · No sign-up

The method

Formula and calculation steps

V=side³; ρ=m/V.

Calculate sample density from measured mass and cube dimensions.

  1. Confirm the sample, reference state, measurement basis and units.
  2. Enter actual measurements and compatible reference values.
  3. Submit the form, then interpret the result with the assumptions and limits below.

The shape is idealized and solid. Cavities, pores, coatings and measurement tolerances affect the inferred density.

Cube Density: method and interpretation

Calculate sample density from measured mass and cube dimensions. The shape is idealized and solid. Cavities, pores, coatings and measurement tolerances affect the inferred density.

Measure actual sample dimensions and tare any container before weighing. A hollow object’s outside envelope gives apparent average density, while material-only volume gives a different quantity. Liquid displacement can fail when a sample absorbs, dissolves or traps air.

Density is sensitive to dimensional measurement: cylinder and sphere volume contain a squared or cubed dimension. The comparison table varies the stated measurement and assumes the remaining measurements are exact; it is not a laboratory uncertainty budget.

Check the numbers

Cube Density Calculator: calculated examples

These scenarios are computed with the same method as the form. They are not product recommendations, code design values or complete standards tables.

Worked example with stated inputs

Dimension units = Metric dimensions; Measured mass = 1 ; Mass unit = kg; Measured cube side = 100 mm.

OutputComputed result
Density from measured shape1,000 kg/m³
Measured / envelope volume0.001 m³
Measured / envelope volume0.035315 ft³
Mass1 kg
Mass density1 g/cm³ or g/mL
Mass density62.427961 lb/ft³
Mass density0.036127 lb/in³
Mass density8.345404 lb/US gal
Mass density10.022413 lb/Imperial gal

How the stated input changes the result

ScenarioChanged input / basisResult
50 mmMeasured cube side8,000 kg/m³
75 mmMeasured cube side2,370.37037 kg/m³
100 mmMeasured cube side1,000 kg/m³
125 mmMeasured cube side512 kg/m³
150 mmMeasured cube side296.296296 kg/m³
200 mmMeasured cube side125 kg/m³

Unchanged inputs use: Dimension units = Metric dimensions; Measured mass = 1 ; Mass unit = kg; Measured cube side = 100 mm. Results retain the model limitations described above.

Common questions

What measurement or model limitation matters here?

The shape is idealized and solid. Cavities, pores, coatings and measurement tolerances affect the inferred density.

How are the example tables calculated?

Each row changes the labelled measured cube side while retaining the other worked-example inputs. The table uses the same V=side³; ρ=m/V. calculation as the form.

How do I use this cube density calculator?

Calculate sample density from measured mass and cube dimensions. V=side³; ρ=m/V.

Which units should I enter?

Use the unit printed beside each input or chosen in its selector. The dimension-unit switch converts only the length or area fields that carry it. Other quantities retain their printed units. Mass density has dimensions M L⁻³; a ratio, number per area or probability density is a different quantity.

Are starting values measured material or reference data?

They are editable worked-example inputs unless a specific source and reference condition are explicitly identified. Measure or obtain the properties appropriate to the actual sample, temperature and method.

Can I export the result to Excel?

After calculating, Export CSV saves numerical results and submitted inputs. CSV is a text table, not an Excel formula workbook or a certified test report.

Where are the formula sources?

Full source addresses are printed below as ordinary text. The equations, worked examples and comparison tables are contained in these pages and do not require an online data service.

Formula sources and references

References support the underlying methods and units. Chosen example inputs are not universal recommendations, supplier ratings, market prices or code limits.

  • OpenStax Prealgebra: geometry applications, volume and surface areahttps://openstax.org/books/prealgebra/pages/9-6-solve-geometry-applications-volume-and-surface-area
  • OpenStax University Physics: density, pressure and mass per volumehttps://openstax.org/books/university-physics-volume-1/pages/14-1-fluids-density-and-pressure
  • NIST Guide to the SI: conversion factorshttps://www.nist.gov/pml/special-publication-811/nist-guide-si-appendix-b-conversion-factors