Density CalculatorMeasure mass. Define volume.

Density calculators / Optics & display density

A clear measure of matter.

Pixel Density Calculator

Calculate native display pixels per inch and square-pixel pitch.

Your measurements & units

pixels
pixels
inches

Starting values are editable examples. Confirm the sample, measurement basis and units. Dimension switching converts only the labelled geometry fields; other unit selectors describe the numbers you enter.

Reset

Your result

Ready to calculate

Enter your values and press Calculate. The result will open on the calculation page.

Published references · Clear assumptions · No sign-up

The method

Formula and calculation steps

PPI=√(horizontal²+vertical²)/diagonal inches; pitch=25.4/PPI mm.

Calculate native display pixels per inch and square-pixel pitch.

  1. Confirm the sample, reference state, measurement basis and units.
  2. Enter actual measurements and compatible reference values.
  3. Submit the form, then interpret the result with the assumptions and limits below.

Flat rectangular active area and square pixels. Screen PPI differs from printer DPI, CSS pixel ratio or operating-system scaling.

Pixel Density: method and interpretation

Calculate native display pixels per inch and square-pixel pitch. Flat rectangular active area and square pixels. Screen PPI differs from printer DPI, CSS pixel ratio or operating-system scaling.

Optical density is a base-ten logarithmic attenuation measure at a stated wavelength; display pixel density is a geometric count of pixels per inch. Neither is a mass-per-volume property, and their numerical values cannot be compared as though they had the same unit.

Use consistent measurement geometry for optical transmission and the native active dimensions for a display. A numerical optical density is not an eyewear recommendation, and a panel’s PPI does not describe software scaling or printer-dot performance.

Check the numbers

Pixel Density Calculator: calculated examples

These scenarios are computed with the same method as the form. They are not product recommendations, code design values or complete standards tables.

Worked example with stated inputs

Native horizontal pixels = 3840 pixels; Native vertical pixels = 2160 pixels; Active screen diagonal = 27 inches.

OutputComputed result
Native active-screen pixel density163.178309 PPI
Square-pixel pitch0.155658 mm/pixel

How the stated input changes the result

ScenarioChanged input / basisResult
13.5 inchesActive screen diagonal326.356618 PPI
20.25 inchesActive screen diagonal217.571079 PPI
27 inchesActive screen diagonal163.178309 PPI
33.75 inchesActive screen diagonal130.542647 PPI
40.5 inchesActive screen diagonal108.785539 PPI
54 inchesActive screen diagonal81.589154 PPI

Unchanged inputs use: Native horizontal pixels = 3840 pixels; Native vertical pixels = 2160 pixels; Active screen diagonal = 27 inches. Results retain the model limitations described above.

Common questions

What measurement or model limitation matters here?

Flat rectangular active area and square pixels. Screen PPI differs from printer DPI, CSS pixel ratio or operating-system scaling.

How are the example tables calculated?

Each row changes the labelled active screen diagonal while retaining the other worked-example inputs. The table uses the same PPI=√(horizontal²+vertical²)/diagonal inches; pitch=25.4/PPI mm. calculation as the form.

How do I use this pixel density calculator?

Calculate native display pixels per inch and square-pixel pitch. PPI=√(horizontal²+vertical²)/diagonal inches; pitch=25.4/PPI mm.

Which units should I enter?

Use the specific units printed beside each field. The resulting ratio, score or concentration has the meaning stated in the formula; it is not interchangeable with material mass density. Reference quantities and measurement conventions must match.

Are starting values measured material or reference data?

They are editable worked-example inputs unless a specific source and reference condition are explicitly identified. Measure or obtain the properties appropriate to the actual sample, temperature and method.

Can I export the result to Excel?

After calculating, Export CSV saves numerical results and submitted inputs. CSV is a text table, not an Excel formula workbook or a certified test report.

Where are the formula sources?

Full source addresses are printed below as ordinary text. The equations, worked examples and comparison tables are contained in these pages and do not require an online data service.

Formula sources and references

References support the underlying methods and units. Chosen example inputs are not universal recommendations, supplier ratings, market prices or code limits.

  • EIZO: How Pixel Density Works in the Age of 4Khttps://www.eizo.com/library/basics/pixel_density_4k/
  • NIST Guide to the SI: conversion factorshttps://www.nist.gov/pml/special-publication-811/nist-guide-si-appendix-b-conversion-factors