Density CalculatorMeasure mass. Define volume.

Density calculators / Optics & display density

A clear measure of matter.

Optical Density Calculator

Convert percentage transmission into optical density for the same wavelength and measurement geometry.

Your measurements & units

%

Starting values are editable examples. Confirm the sample, measurement basis and units. Dimension switching converts only the labelled geometry fields; other unit selectors describe the numbers you enter.

Reset

Your result

Ready to calculate

Enter your values and press Calculate. The result will open on the calculation page.

Published references · Clear assumptions · No sign-up

The method

Formula and calculation steps

OD=−log10(Tfraction).

Convert percentage transmission into optical density for the same wavelength and measurement geometry.

  1. Confirm the sample, reference state, measurement basis and units.
  2. Enter actual measurements and compatible reference values.
  3. Submit the form, then interpret the result with the assumptions and limits below.

Passive attenuation only. OD is logarithmic, not transmission percent; this does not select laser-protective eyewear.

Optical Density: method and interpretation

Convert percentage transmission into optical density for the same wavelength and measurement geometry. Passive attenuation only. OD is logarithmic, not transmission percent; this does not select laser-protective eyewear.

Optical density is a base-ten logarithmic attenuation measure at a stated wavelength; display pixel density is a geometric count of pixels per inch. Neither is a mass-per-volume property, and their numerical values cannot be compared as though they had the same unit.

Use consistent measurement geometry for optical transmission and the native active dimensions for a display. A numerical optical density is not an eyewear recommendation, and a panel’s PPI does not describe software scaling or printer-dot performance.

Check the numbers

Optical Density Calculator: calculated examples

These scenarios are computed with the same method as the form. They are not product recommendations, code design values or complete standards tables.

Worked example with stated inputs

Measured transmission = 10 %.

OutputComputed result
Optical density for supplied transmission1 OD
Transmission fraction0.1

How the stated input changes the result

ScenarioChanged input / basisResult
5 %Measured transmission1.30103 OD
7.5 %Measured transmission1.124939 OD
10 %Measured transmission1 OD
12.5 %Measured transmission0.90309 OD
15 %Measured transmission0.823909 OD
20 %Measured transmission0.69897 OD

Unchanged inputs use: Measured transmission = 10 %. Results retain the model limitations described above.

Common questions

What measurement or model limitation matters here?

Passive attenuation only. OD is logarithmic, not transmission percent; this does not select laser-protective eyewear.

How are the example tables calculated?

Each row changes the labelled measured transmission while retaining the other worked-example inputs. The table uses the same OD=−log10(Tfraction). calculation as the form.

How do I use this optical density calculator?

Convert percentage transmission into optical density for the same wavelength and measurement geometry. OD=−log10(Tfraction).

Which units should I enter?

Use the specific units printed beside each field. The resulting ratio, score or concentration has the meaning stated in the formula; it is not interchangeable with material mass density. Reference quantities and measurement conventions must match.

Are starting values measured material or reference data?

They are editable worked-example inputs unless a specific source and reference condition are explicitly identified. Measure or obtain the properties appropriate to the actual sample, temperature and method.

Can I export the result to Excel?

After calculating, Export CSV saves numerical results and submitted inputs. CSV is a text table, not an Excel formula workbook or a certified test report.

Where are the formula sources?

Full source addresses are printed below as ordinary text. The equations, worked examples and comparison tables are contained in these pages and do not require an online data service.

Formula sources and references

References support the underlying methods and units. Chosen example inputs are not universal recommendations, supplier ratings, market prices or code limits.

  • Edmund Optics: Optical Filters, optical-density equationshttps://www.edmundoptics.com/knowledge-center/application-notes/optics/optical-filters/
  • NIST Guide to the SI: conversion factorshttps://www.nist.gov/pml/special-publication-811/nist-guide-si-appendix-b-conversion-factors