Density CalculatorMeasure mass. Define volume.

Density calculators / Crystal & number density

A clear measure of matter.

Number Density Calculator

Convert a mass density into particle or formula-unit number per cubic metre.

Your measurements & units

g/mol

Starting values are editable examples. Confirm the sample, measurement basis and units. Dimension switching converts only the labelled geometry fields; other unit selectors describe the numbers you enter.

Reset

Your result

Ready to calculate

Enter your values and press Calculate. The result will open on the calculation page.

Published references · Clear assumptions · No sign-up

The method

Formula and calculation steps

Number density=ρ NA/M, with M in kg/mol.

Convert a mass density into particle or formula-unit number per cubic metre.

  1. Confirm the sample, reference state, measurement basis and units.
  2. Enter actual measurements and compatible reference values.
  3. Submit the form, then interpret the result with the assumptions and limits below.

Specify what M counts: molecules, atoms or formula units. This does not infer free-electron density or ionization state.

Number Density: method and interpretation

Convert a mass density into particle or formula-unit number per cubic metre. Specify what M counts: molecules, atoms or formula units. This does not infer free-electron density or ionization state.

The counted entity must match the molar mass. Atoms, molecules, formula units and mobile electrons are different entities. The Avogadro constant converts a defined amount of substance to a count; it does not identify the material or its electronic state.

A theoretical crystal density uses a supplied cell geometry, matching formula-unit count and occupancy assumptions. Actual defects, vacancies, temperature and porosity can make a specimen’s measured density differ from the ideal cell value.

Check the numbers

Number Density Calculator: calculated examples

These scenarios are computed with the same method as the form. They are not product recommendations, code design values or complete standards tables.

Worked example with stated inputs

Mass density = 1000 ; Density unit = kg/m³; Molar mass = 18.0153 g/mol.

OutputComputed result
Number density for stated molar entity3.342796e+28 entities/m³
Molar number concentration55,508.435062 mol/m³

How the stated input changes the result

ScenarioChanged input / basisResult
500 Mass density1.671398e+28 entities/m³
750 Mass density2.507097e+28 entities/m³
1000 Mass density3.342796e+28 entities/m³
1250 Mass density4.178495e+28 entities/m³
1500 Mass density5.014194e+28 entities/m³
2000 Mass density6.685592e+28 entities/m³

Unchanged inputs use: Mass density = 1000 ; Density unit = kg/m³; Molar mass = 18.0153 g/mol. Results retain the model limitations described above.

Common questions

What measurement or model limitation matters here?

Specify what M counts: molecules, atoms or formula units. This does not infer free-electron density or ionization state.

How are the example tables calculated?

Each row changes the labelled mass density while retaining the other worked-example inputs. The table uses the same Number density=ρ NA/M, with M in kg/mol. calculation as the form.

How do I use this number density calculator?

Convert a mass density into particle or formula-unit number per cubic metre. Number density=ρ NA/M, with M in kg/mol.

Which units should I enter?

Use the unit printed beside each input or chosen in its selector. The dimension-unit switch converts only the length or area fields that carry it. Other quantities retain their printed units. Mass density has dimensions M L⁻³; a ratio, number per area or probability density is a different quantity.

Are starting values measured material or reference data?

They are editable worked-example inputs unless a specific source and reference condition are explicitly identified. Measure or obtain the properties appropriate to the actual sample, temperature and method.

Can I export the result to Excel?

After calculating, Export CSV saves numerical results and submitted inputs. CSV is a text table, not an Excel formula workbook or a certified test report.

Where are the formula sources?

Full source addresses are printed below as ordinary text. The equations, worked examples and comparison tables are contained in these pages and do not require an online data service.

Formula sources and references

References support the underlying methods and units. Chosen example inputs are not universal recommendations, supplier ratings, market prices or code limits.

  • NIST SP 330, Section 2: defining constants of the SIhttps://www.nist.gov/pml/special-publication-330/sp-330-section-2
  • OpenStax University Physics: density, pressure and mass per volumehttps://openstax.org/books/university-physics-volume-1/pages/14-1-fluids-density-and-pressure
  • NIST Guide to the SI: conversion factorshttps://www.nist.gov/pml/special-publication-811/nist-guide-si-appendix-b-conversion-factors