Density CalculatorMeasure mass. Define volume.

Density calculators / Statistics & distributions

A clear measure of matter.

Frequency Density Calculator

Calculate count-based histogram height for an explicitly defined class interval.

Your measurements & units

count
input units
input units

Starting values are editable examples. Confirm the sample, measurement basis and units. Dimension switching converts only the labelled geometry fields; other unit selectors describe the numbers you enter.

Reset

Your result

Ready to calculate

Enter your values and press Calculate. The result will open on the calculation page.

Published references · Clear assumptions · No sign-up

The method

Formula and calculation steps

Histogram frequency density=class frequency/(upper boundary−lower boundary).

Calculate count-based histogram height for an explicitly defined class interval.

  1. Confirm the sample, reference state, measurement basis and units.
  2. Enter actual measurements and compatible reference values.
  3. Submit the form, then interpret the result with the assumptions and limits below.

The class width must be positive. A normalized probability histogram additionally divides by total sample count; these heights are not probabilities by themselves.

Frequency Density: method and interpretation

Calculate count-based histogram height for an explicitly defined class interval. The class width must be positive. A normalized probability histogram additionally divides by total sample count; these heights are not probabilities by themselves.

A continuous probability density is a height in reciprocal variable units. Probability is an integral over an interval; a density may exceed one without violating probability rules. Histogram frequency density uses a count-per-class-width convention unless it is explicitly normalized.

Choose a distribution and parameters justified by the data. This page evaluates only its stated model, without fitting an arbitrary function. Spectral density has a separate frequency denominator and requires an explicit one-sided or two-sided convention before integration.

Check the numbers

Frequency Density Calculator: calculated examples

These scenarios are computed with the same method as the form. They are not product recommendations, code design values or complete standards tables.

Worked example with stated inputs

Class frequency = 20 count; Lower class boundary = 10 input units; Upper class boundary = 20 input units.

OutputComputed result
Histogram frequency density2 count/input unit
Class width10 input units

How the stated input changes the result

ScenarioChanged input / basisResult
10 countClass frequency1 count/input unit
15 countClass frequency1.5 count/input unit
20 countClass frequency2 count/input unit
25 countClass frequency2.5 count/input unit
30 countClass frequency3 count/input unit
40 countClass frequency4 count/input unit

Unchanged inputs use: Class frequency = 20 count; Lower class boundary = 10 input units; Upper class boundary = 20 input units. Results retain the model limitations described above.

Common questions

What measurement or model limitation matters here?

The class width must be positive. A normalized probability histogram additionally divides by total sample count; these heights are not probabilities by themselves.

How are the example tables calculated?

Each row changes the labelled class frequency while retaining the other worked-example inputs. The table uses the same Histogram frequency density=class frequency/(upper boundary−lower boundary). calculation as the form.

How do I use this frequency density calculator?

Calculate count-based histogram height for an explicitly defined class interval. Histogram frequency density=class frequency/(upper boundary−lower boundary).

Which units should I enter?

Use the specific units printed beside each field. The resulting ratio, score or concentration has the meaning stated in the formula; it is not interchangeable with material mass density. Reference quantities and measurement conventions must match.

Are starting values measured material or reference data?

They are editable worked-example inputs unless a specific source and reference condition are explicitly identified. Measure or obtain the properties appropriate to the actual sample, temperature and method.

Can I export the result to Excel?

After calculating, Export CSV saves numerical results and submitted inputs. CSV is a text table, not an Excel formula workbook or a certified test report.

Where are the formula sources?

Full source addresses are printed below as ordinary text. The equations, worked examples and comparison tables are contained in these pages and do not require an online data service.

Formula sources and references

References support the underlying methods and units. Chosen example inputs are not universal recommendations, supplier ratings, market prices or code limits.

  • OCR GCSE Mathematics J560/04 November 2023 examiners’ report, histogram formula correctionhttps://ocr-live-prd95.cambridgeassessment.org.uk/Images/722462-examiners-report-paper-4.pdf
  • NIST Guide to the SI: conversion factorshttps://www.nist.gov/pml/special-publication-811/nist-guide-si-appendix-b-conversion-factors