Density CalculatorMeasure mass. Define volume.

Density calculators / Gas, air & temperature

A clear measure of matter.

Steam Density from Specific Volume Calculator

Calculate steam density from a supplied specific volume at its known operating state.

Your measurements & units

m³/kg

Starting values are editable examples. Confirm the sample, measurement basis and units. Dimension switching converts only the labelled geometry fields; other unit selectors describe the numbers you enter.

Reset

Your result

Ready to calculate

Enter your values and press Calculate. The result will open on the calculation page.

Published references · Clear assumptions · No sign-up

The method

Formula and calculation steps

ρ=1/vspecific.

Calculate steam density from a supplied specific volume at its known operating state.

  1. Confirm the sample, reference state, measurement basis and units.
  2. Enter actual measurements and compatible reference values.
  3. Submit the form, then interpret the result with the assumptions and limits below.

No automatic saturated or superheated steam table. Use a state-specific value; this reciprocal cannot infer pressure, temperature or vapor quality.

Steam Density from Specific Volume: method and interpretation

Calculate steam density from a supplied specific volume at its known operating state. No automatic saturated or superheated steam table. Use a state-specific value; this reciprocal cannot infer pressure, temperature or vapor quality.

Gas density changes with absolute pressure, absolute temperature, composition and nonideal behavior. Gauge pressure must first be converted using the actual atmospheric reference. A supplied compressibility factor is not automatically a real-gas property calculation.

Standard atmosphere describes a reference profile rather than observed weather. Water and moist-air equations have explicit temperature and pressure boundaries. Cryogenic liquids, steam tables, salinity and supercritical properties cannot be inferred from an ideal-gas or pure-water relation.

Check the numbers

Steam Density from Specific Volume Calculator: calculated examples

These scenarios are computed with the same method as the form. They are not product recommendations, code design values or complete standards tables.

Worked example with stated inputs

Supplied operating steam specific volume = 0.2 m³/kg.

OutputComputed result
Density from specific volume5 kg/m³
Mass density0.005 g/cm³ or g/mL
Mass density0.31214 lb/ft³
Mass density0.000181 lb/in³
Mass density0.041727 lb/US gal
Mass density0.050112 lb/Imperial gal

How the stated input changes the result

ScenarioChanged input / basisResult
0.1 m³/kgSupplied operating steam specific volume10 kg/m³
0.15 m³/kgSupplied operating steam specific volume6.666667 kg/m³
0.2 m³/kgSupplied operating steam specific volume5 kg/m³
0.25 m³/kgSupplied operating steam specific volume4 kg/m³
0.3 m³/kgSupplied operating steam specific volume3.333333 kg/m³
0.4 m³/kgSupplied operating steam specific volume2.5 kg/m³

Unchanged inputs use: Supplied operating steam specific volume = 0.2 m³/kg. Results retain the model limitations described above.

Common questions

What measurement or model limitation matters here?

No automatic saturated or superheated steam table. Use a state-specific value; this reciprocal cannot infer pressure, temperature or vapor quality.

How are the example tables calculated?

Each row changes the labelled supplied operating steam specific volume while retaining the other worked-example inputs. The table uses the same ρ=1/vspecific. calculation as the form.

How do I use this steam density from specific volume calculator?

Calculate steam density from a supplied specific volume at its known operating state. ρ=1/vspecific.

Which units should I enter?

Use the unit printed beside each input or chosen in its selector. The dimension-unit switch converts only the length or area fields that carry it. Other quantities retain their printed units. Mass density has dimensions M L⁻³; a ratio, number per area or probability density is a different quantity.

Are starting values measured material or reference data?

They are editable worked-example inputs unless a specific source and reference condition are explicitly identified. Measure or obtain the properties appropriate to the actual sample, temperature and method.

Can I export the result to Excel?

After calculating, Export CSV saves numerical results and submitted inputs. CSV is a text table, not an Excel formula workbook or a certified test report.

Where are the formula sources?

Full source addresses are printed below as ordinary text. The equations, worked examples and comparison tables are contained in these pages and do not require an online data service.

Formula sources and references

References support the underlying methods and units. Chosen example inputs are not universal recommendations, supplier ratings, market prices or code limits.

  • NASA Glenn: Equation of State, ideal gas lawhttps://www1.grc.nasa.gov/beginners-guide-to-aeronautics/equation-of-state/
  • NIST Guide to the SI: conversion factorshttps://www.nist.gov/pml/special-publication-811/nist-guide-si-appendix-b-conversion-factors