Density calculators / Physical density measures
A clear measure of matter.
Magnetic Flux Density Calculator
Calculate magnetic flux density using explicitly supplied geometry and measured or stated input.
Your measurements & units
Your result
Ready to calculateEnter your values and press Calculate. The result will open on the calculation page.
Published references · Clear assumptions · No sign-up
The method
Formula and calculation steps
B=Φ/(A cosθ).
Calculate magnetic flux density using explicitly supplied geometry and measured or stated input.
- Confirm the sample, reference state, measurement basis and units.
- Enter actual measurements and compatible reference values.
- Submit the form, then interpret the result with the assumptions and limits below.
Uniform magnetic field. Flux per turn is different from winding flux linkage; no saturation or core-loss prediction.
Magnetic Flux Density: method and interpretation
Calculate magnetic flux density using explicitly supplied geometry and measured or stated input. Uniform magnetic field. Flux per turn is different from winding flux linkage; no saturation or core-loss prediction.
The denominator determines the physical quantity: current per cross section, energy per volume, power per area and mass per length are distinct measures. Always retain units when comparing values, especially gravimetric and volumetric battery energy.
Area-average calculations assume the stated uniform distribution or ideal geometry. They do not establish safe conductor current, laser protection, RF exposure compliance, lighting-code acceptance or material strength. Those decisions require the relevant full design and measurement context.
Continue with: Linear Mass Density Calculator · Surface Mass Density Calculator · Current Density Calculator · PCB Trace Current Density Calculator
Check the numbers
Magnetic Flux Density Calculator: calculated examples
These scenarios are computed with the same method as the form. They are not product recommendations, code design values or complete standards tables.
Worked example with stated inputs
Flux per turn = 0.001 Wb; Planar area = 0.01 m²; Field angle from area normal = 0 degrees.
| Output | Computed result |
|---|---|
| Uniform magnetic flux density | 0.1 T |
| Flux density | 100 mT |
How the stated input changes the result
| Scenario | Changed input / basis | Result |
|---|---|---|
| 0.005 m² | Planar area | 0.2 T |
| 0.0075 m² | Planar area | 0.133333 T |
| 0.01 m² | Planar area | 0.1 T |
| 0.0125 m² | Planar area | 0.08 T |
| 0.015 m² | Planar area | 0.066667 T |
| 0.02 m² | Planar area | 0.05 T |
Unchanged inputs use: Flux per turn = 0.001 Wb; Planar area = 0.01 m²; Field angle from area normal = 0 degrees. Results retain the model limitations described above.
Common questions
What measurement or model limitation matters here?
Uniform magnetic field. Flux per turn is different from winding flux linkage; no saturation or core-loss prediction.
How are the example tables calculated?
Each row changes the labelled planar area while retaining the other worked-example inputs. The table uses the same B=Φ/(A cosθ). calculation as the form.
How do I use this magnetic flux density calculator?
Calculate magnetic flux density using explicitly supplied geometry and measured or stated input. B=Φ/(A cosθ).
Which units should I enter?
Use the unit printed beside each input or chosen in its selector. The dimension-unit switch converts only the length or area fields that carry it. Other quantities retain their printed units. Mass density has dimensions M L⁻³; a ratio, number per area or probability density is a different quantity.
Are starting values measured material or reference data?
They are editable worked-example inputs unless a specific source and reference condition are explicitly identified. Measure or obtain the properties appropriate to the actual sample, temperature and method.
Can I export the result to Excel?
After calculating, Export CSV saves numerical results and submitted inputs. CSV is a text table, not an Excel formula workbook or a certified test report.
Where are the formula sources?
Full source addresses are printed below as ordinary text. The equations, worked examples and comparison tables are contained in these pages and do not require an online data service.
Related calculators
Formula sources and references
References support the underlying methods and units. Chosen example inputs are not universal recommendations, supplier ratings, market prices or code limits.
- OpenStax University Physics Volume 2, 13.1: Faraday’s Lawhttps://openstax.org/books/university-physics-volume-2/pages/13-1-faradays-law
- NIST Guide to the SI: conversion factorshttps://www.nist.gov/pml/special-publication-811/nist-guide-si-appendix-b-conversion-factors