Density CalculatorMeasure mass. Define volume.

Density calculators / Gas, air & temperature

A clear measure of matter.

Gas Mixture Density Calculator

Calculate a two-component gas density using mole fractions and a supplied mixture compressibility factor.

Your measurements & units

ratio
g/mol
g/mol
kPa absolute
K
ratio

Starting values are editable examples. Confirm the sample, measurement basis and units. Dimension switching converts only the labelled geometry fields; other unit selectors describe the numbers you enter.

Reset

Your result

Ready to calculate

Enter your values and press Calculate. The result will open on the calculation page.

Published references · Clear assumptions · No sign-up

The method

Formula and calculation steps

Mmix=y1 M1+(1−y1)M2; ρ=pMmix/(ZRT).

Calculate a two-component gas density using mole fractions and a supplied mixture compressibility factor.

  1. Confirm the sample, reference state, measurement basis and units.
  2. Enter actual measurements and compatible reference values.
  3. Submit the form, then interpret the result with the assumptions and limits below.

Mole fractions are not mass fractions. No reaction, condensation or automatic mixing rule for Z.

Gas Mixture Density: method and interpretation

Calculate a two-component gas density using mole fractions and a supplied mixture compressibility factor. Mole fractions are not mass fractions. No reaction, condensation or automatic mixing rule for Z.

Gas density changes with absolute pressure, absolute temperature, composition and nonideal behavior. Gauge pressure must first be converted using the actual atmospheric reference. A supplied compressibility factor is not automatically a real-gas property calculation.

Standard atmosphere describes a reference profile rather than observed weather. Water and moist-air equations have explicit temperature and pressure boundaries. Cryogenic liquids, steam tables, salinity and supercritical properties cannot be inferred from an ideal-gas or pure-water relation.

Check the numbers

Gas Mixture Density Calculator: calculated examples

These scenarios are computed with the same method as the form. They are not product recommendations, code design values or complete standards tables.

Worked example with stated inputs

Component 1 mole fraction = 0.79 ratio; Component 1 molar mass = 28.0134 g/mol; Component 2 molar mass = 31.9988 g/mol; Absolute pressure = 101.325 kPa absolute; Temperature = 293.15 K; Mixture Z (supplied) = 1 ratio.

OutputComputed result
Gas density for supplied p, T, M and Z1.199343 kg/m³
Molar mass28.850334 g/mol
Specific gas constant288.192941 J/(kg·K)
Absolute pressure101.325 kPa absolute
Mass density0.001199 g/cm³ or g/mL
Mass density0.074873 lb/ft³
Mass density4.332901e-5 lb/in³
Mass density0.010009 lb/US gal
Mass density0.01202 lb/Imperial gal

How the stated input changes the result

ScenarioChanged input / basisResult
0.395 ratioComponent 1 mole fraction1.264786 kg/m³
0.5925 ratioComponent 1 mole fraction1.232064 kg/m³
0.79 ratioComponent 1 mole fraction1.199343 kg/m³
0.9875 ratioComponent 1 mole fraction1.166622 kg/m³
1 ratioComponent 1 mole fraction1.164551 kg/m³
1 ratioComponent 1 mole fraction1.164551 kg/m³

Unchanged inputs use: Component 1 mole fraction = 0.79 ratio; Component 1 molar mass = 28.0134 g/mol; Component 2 molar mass = 31.9988 g/mol; Absolute pressure = 101.325 kPa absolute; Temperature = 293.15 K; Mixture Z (supplied) = 1 ratio. Results retain the model limitations described above.

Common questions

What measurement or model limitation matters here?

Mole fractions are not mass fractions. No reaction, condensation or automatic mixing rule for Z.

How are the example tables calculated?

Each row changes the labelled component 1 mole fraction while retaining the other worked-example inputs. The table uses the same Mmix=y1 M1+(1−y1)M2; ρ=pMmix/(ZRT). calculation as the form.

How do I use this gas mixture density calculator?

Calculate a two-component gas density using mole fractions and a supplied mixture compressibility factor. Mmix=y1 M1+(1−y1)M2; ρ=pMmix/(ZRT).

Which units should I enter?

Use the unit printed beside each input or chosen in its selector. The dimension-unit switch converts only the length or area fields that carry it. Other quantities retain their printed units. Mass density has dimensions M L⁻³; a ratio, number per area or probability density is a different quantity.

Are starting values measured material or reference data?

They are editable worked-example inputs unless a specific source and reference condition are explicitly identified. Measure or obtain the properties appropriate to the actual sample, temperature and method.

Can I export the result to Excel?

After calculating, Export CSV saves numerical results and submitted inputs. CSV is a text table, not an Excel formula workbook or a certified test report.

Where are the formula sources?

Full source addresses are printed below as ordinary text. The equations, worked examples and comparison tables are contained in these pages and do not require an online data service.

Formula sources and references

References support the underlying methods and units. Chosen example inputs are not universal recommendations, supplier ratings, market prices or code limits.

  • NASA Glenn: Equation of State, ideal gas lawhttps://www1.grc.nasa.gov/beginners-guide-to-aeronautics/equation-of-state/
  • NIST Guide to the SI: conversion factorshttps://www.nist.gov/pml/special-publication-811/nist-guide-si-appendix-b-conversion-factors
  • Penn State: Z-factor definition and PV=ZnRThttps://courses.ems.psu.edu/png520/node/1945