Density CalculatorMeasure mass. Define volume.

Density calculators / Gas, air & temperature

A clear measure of matter.

Density Altitude Calculator

Find the standard-atmosphere height equivalent to the dry-air density calculated from actual station pressure and temperature.

Your measurements & units

kPa absolute
°C

Starting values are editable examples. Confirm the sample, measurement basis and units. Dimension switching converts only the labelled geometry fields; other unit selectors describe the numbers you enter.

Reset

Your result

Ready to calculate

Enter your values and press Calculate. The result will open on the calculation page.

Published references · Clear assumptions · No sign-up

The method

Formula and calculation steps

ρ=p/(RdT); hρ=(288.15/0.0065)[1−(ρ/ρ0)^(1/4.255877)].

Find the standard-atmosphere height equivalent to the dry-air density calculated from actual station pressure and temperature.

  1. Confirm the sample, reference state, measurement basis and units.
  2. Enter actual measurements and compatible reference values.
  3. Submit the form, then interpret the result with the assumptions and limits below.

0–11000 m equivalent ISA height only. Do not substitute altimeter setting for station pressure. Humidity and aircraft performance are not modeled; this educational estimate is not flight-planning data.

Density Altitude: method and interpretation

Find the standard-atmosphere height equivalent to the dry-air density calculated from actual station pressure and temperature. 0–11000 m equivalent ISA height only. Do not substitute altimeter setting for station pressure. Humidity and aircraft performance are not modeled; this educational estimate is not flight-planning data.

Gas density changes with absolute pressure, absolute temperature, composition and nonideal behavior. Gauge pressure must first be converted using the actual atmospheric reference. A supplied compressibility factor is not automatically a real-gas property calculation.

Standard atmosphere describes a reference profile rather than observed weather. Water and moist-air equations have explicit temperature and pressure boundaries. Cryogenic liquids, steam tables, salinity and supercritical properties cannot be inferred from an ideal-gas or pure-water relation.

Check the numbers

Density Altitude Calculator: calculated examples

These scenarios are computed with the same method as the form. They are not product recommendations, code design values or complete standards tables.

Worked example with stated inputs

Measured station absolute pressure = 90 kPa absolute; Measured dry air temperature = 30 °C.

OutputComputed result
Dry-air density altitude estimate1,728.575341 m ISA equivalent
Equivalent standard height5,671.178941 ft
Calculated dry-air density1.034244 kg/m³

How the stated input changes the result

ScenarioChanged input / basisResult
15 °CMeasured dry air temperature1,217.551375 m ISA equivalent
22.5 °CMeasured dry air temperature1,477.066128 m ISA equivalent
30 °CMeasured dry air temperature1,728.575341 m ISA equivalent
37.5 °CMeasured dry air temperature1,972.515065 m ISA equivalent
45 °CMeasured dry air temperature2,209.287787 m ISA equivalent
60 °CMeasured dry air temperature2,662.793802 m ISA equivalent

Unchanged inputs use: Measured station absolute pressure = 90 kPa absolute; Measured dry air temperature = 30 °C. Results retain the model limitations described above.

Common questions

What measurement or model limitation matters here?

0–11000 m equivalent ISA height only. Do not substitute altimeter setting for station pressure. Humidity and aircraft performance are not modeled; this educational estimate is not flight-planning data.

How are the example tables calculated?

Each row changes the labelled measured dry air temperature while retaining the other worked-example inputs. The table uses the same ρ=p/(RdT); hρ=(288.15/0.0065)[1−(ρ/ρ0)^(1/4.255877)]. calculation as the form.

How do I use this density altitude calculator?

Find the standard-atmosphere height equivalent to the dry-air density calculated from actual station pressure and temperature. ρ=p/(RdT); hρ=(288.15/0.0065)[1−(ρ/ρ0)^(1/4.255877)].

Which units should I enter?

Use the unit printed beside each input or chosen in its selector. The dimension-unit switch converts only the length or area fields that carry it. Other quantities retain their printed units. Mass density has dimensions M L⁻³; a ratio, number per area or probability density is a different quantity.

Are starting values measured material or reference data?

They are editable worked-example inputs unless a specific source and reference condition are explicitly identified. Measure or obtain the properties appropriate to the actual sample, temperature and method.

Can I export the result to Excel?

After calculating, Export CSV saves numerical results and submitted inputs. CSV is a text table, not an Excel formula workbook or a certified test report.

Where are the formula sources?

Full source addresses are printed below as ordinary text. The equations, worked examples and comparison tables are contained in these pages and do not require an online data service.

Formula sources and references

References support the underlying methods and units. Chosen example inputs are not universal recommendations, supplier ratings, market prices or code limits.

  • Roland Stull, UBC: Meteorology for Scientists and Engineers, Chapter 1, equations 1.16–1.20https://www.eoas.ubc.ca/books/Practical_Meteorology/mse3/Ch01-Atmos.pdf
  • US National Weather Service: Density Altitude; actual station pressure and virtual temperaturehttps://www.weather.gov/media/epz/wxcalc/densityAltitude.pdf
  • NIST Guide to the SI: conversion factorshttps://www.nist.gov/pml/special-publication-811/nist-guide-si-appendix-b-conversion-factors