Density calculators / Physical density measures
A clear measure of matter.
Antenna Power Flux Density Calculator
Calculate ideal far-field directional power per spherical area from supplied radiated power and linear gain.
Your measurements & units
Your result
Ready to calculateEnter your values and press Calculate. The result will open on the calculation page.
Published references · Clear assumptions · No sign-up
The method
Formula and calculation steps
S=P G/(4πr²).
Calculate ideal far-field directional power per spherical area from supplied radiated power and linear gain.
- Confirm the sample, reference state, measurement basis and units.
- Enter actual measurements and compatible reference values.
- Submit the form, then interpret the result with the assumptions and limits below.
Spherical far-field conservation model, with gain expressed as a linear ratio. No near-field pattern, reflection, obstruction, exposure-compliance decision or safe distance recommendation.
Antenna Power Flux Density: method and interpretation
Calculate ideal far-field directional power per spherical area from supplied radiated power and linear gain. Spherical far-field conservation model, with gain expressed as a linear ratio. No near-field pattern, reflection, obstruction, exposure-compliance decision or safe distance recommendation.
The denominator determines the physical quantity: current per cross section, energy per volume, power per area and mass per length are distinct measures. Always retain units when comparing values, especially gravimetric and volumetric battery energy.
Area-average calculations assume the stated uniform distribution or ideal geometry. They do not establish safe conductor current, laser protection, RF exposure compliance, lighting-code acceptance or material strength. Those decisions require the relevant full design and measurement context.
Continue with: Linear Mass Density Calculator · Surface Mass Density Calculator · Current Density Calculator · PCB Trace Current Density Calculator
Check the numbers
Antenna Power Flux Density Calculator: calculated examples
These scenarios are computed with the same method as the form. They are not product recommendations, code design values or complete standards tables.
Worked example with stated inputs
Dimension units = Metric dimensions; Total radiated power = 10 W; Directional linear power gain = 1 linear ratio; Far-field distance = 10 m.
| Output | Computed result |
|---|---|
| Ideal far-field directional power density | 0.007958 W/m² |
How the stated input changes the result
| Scenario | Changed input / basis | Result |
|---|---|---|
| 5 m | Far-field distance | 0.031831 W/m² |
| 7.5 m | Far-field distance | 0.014147 W/m² |
| 10 m | Far-field distance | 0.007958 W/m² |
| 12.5 m | Far-field distance | 0.005093 W/m² |
| 15 m | Far-field distance | 0.003537 W/m² |
| 20 m | Far-field distance | 0.001989 W/m² |
Unchanged inputs use: Dimension units = Metric dimensions; Total radiated power = 10 W; Directional linear power gain = 1 linear ratio; Far-field distance = 10 m. Results retain the model limitations described above.
Common questions
What measurement or model limitation matters here?
Spherical far-field conservation model, with gain expressed as a linear ratio. No near-field pattern, reflection, obstruction, exposure-compliance decision or safe distance recommendation.
How are the example tables calculated?
Each row changes the labelled far-field distance while retaining the other worked-example inputs. The table uses the same S=P G/(4πr²). calculation as the form.
How do I use this antenna power flux density calculator?
Calculate ideal far-field directional power per spherical area from supplied radiated power and linear gain. S=P G/(4πr²).
Which units should I enter?
Use the unit printed beside each input or chosen in its selector. The dimension-unit switch converts only the length or area fields that carry it. Other quantities retain their printed units. Mass density has dimensions M L⁻³; a ratio, number per area or probability density is a different quantity.
Are starting values measured material or reference data?
They are editable worked-example inputs unless a specific source and reference condition are explicitly identified. Measure or obtain the properties appropriate to the actual sample, temperature and method.
Can I export the result to Excel?
After calculating, Export CSV saves numerical results and submitted inputs. CSV is a text table, not an Excel formula workbook or a certified test report.
Where are the formula sources?
Full source addresses are printed below as ordinary text. The equations, worked examples and comparison tables are contained in these pages and do not require an online data service.
Related calculators
Formula sources and references
References support the underlying methods and units. Chosen example inputs are not universal recommendations, supplier ratings, market prices or code limits.
- OpenStax University Physics Volume 2, 16.3: Energy Carried by Electromagnetic Waveshttps://openstax.org/books/university-physics-volume-2/pages/16-3-energy-carried-by-electromagnetic-waves
- NIST Guide to the SI: conversion factorshttps://www.nist.gov/pml/special-publication-811/nist-guide-si-appendix-b-conversion-factors